Saved

Press the star next to a tool's name to save it.

All my tools

Stress Calculator

Use this stress calculator to find axial stress from force and area, strain from the change in length, and Young's modulus from the two together, in US or metric units.

Restored your last values ·

Choose stress, strain or Young's modulus and US or metric units. For stress enter the force and the area; for strain the original length and the change in length; for the modulus enter all four.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to find and fill in the boxes, then press Calculate.

See full result

A stress calculator finds the axial stress in a bar from the force and the cross-section area, the strain from the change in length, and Young's modulus from the two together. The same page covers the young modulus calculator, so you can find stress, strain or the elastic modulus of a rod or wire.

How to use the stress calculator

  1. Choose stress, strain or Young's modulus.
  2. Choose US or metric units.
  3. Enter the force and area, the lengths, or all four.
  4. Press Calculate.

Stress

Axial stress is the force per unit of cross-section area: σ = F ÷ A. The Stress (mechanics) page gives this formula for a bar under axial load, with F the force and A the cross-section area [2], and the Young's modulus page describes stress as force per unit area [1]. In metric units, newtons divided by square millimetres give megapascals directly. A positive value means tension and a negative value compression, which is the sign convention on the Stress (mechanics) page [2].

Strain

Strain measures how much a body stretches in proportion to its length: ε = ΔL ÷ L₀, where ΔL is the change in length and L₀ the original length [1]. It can also be written (L₂ − L₁) ÷ L₁, with L₁ the first length and L₂ the final length. Strain has no unit, and the tool also shows it as a percentage. Enter ΔL as a negative number for a shortening. This tool uses engineering strain, the version based on the original length.

Young's modulus

Young's modulus is the ratio of stress to strain, E = σ ÷ ε, the stiffness of the material in the linear region [1]. A stiff material has a large modulus: it needs a big stress for a small strain. The tool gives E in gigapascals for metric inputs and in millions of psi for US inputs, with the gigapascal value beside it. This is also what the young modulus calculator asks for, using the same four numbers.

The linear elastic range

The formulas apply only in the linear elastic range, where stress is proportional to strain, which is Hooke's law [1]. Beyond that range the material may yield or break, and the ratio is no longer a constant. Test numbers well below the yield stress of the material. The tool cannot tell you where that limit is, so check a datasheet and keep any real design far below it.

A worked example

As an example, take a steel rod loaded with 30 kN, 2 m long, with an area of 1 × 10⁻⁴ m², which stretches by 3 mm. In metric units that is F = 30,000 N, A = 100 mm², L₀ = 2,000 mm and ΔL = 3 mm. The stress is 300 MPa, the strain is 0.0015, and E = 300 ÷ 0.0015 = 200,000 MPa, or 200 GPa. These are illustrative numbers, not a measured property of steel.

Comparing with real metals

Wikipedia lists approximate values of 200 GPa for steel (A36) and 68 GPa for aluminium, and says the values are only meant for relative comparison [1]. When you find a modulus, the tool says whether it is close to one of these two figures. This is a sanity check only. Other materials, such as wood, plastics and concrete, have much lower values, and the figure also varies with the alloy and the heat treatment.

US units

With US units the force is in pounds-force, the area in square inches and the lengths in inches, so the stress comes out in pounds per square inch. The tool converts to megapascals using 1 lbf = 4.4482216 N and 1 in = 0.0254 m, which is our own conversion. A force of 1,000 lbf on 2 square inches gives 500 psi, or 3.4474 MPa. A modulus is shown in millions of psi with the gigapascal value.

Tension and compression

A pulling force gives a positive stress and the bar gets longer. A pushing force gives a negative stress, and the bar gets shorter. The tool allows a negative force and a negative change in length so you can model both. For slender members in compression, buckling can occur long before the material stress reaches its limit, and this calculator does not check for that. It handles direct axial load only.

What the page does not cover

This tool covers axial stress only. Shear, combined stress states and thermal stress need other tools. Stress at one point can also differ from the average value that F ÷ A gives [2], for example near holes, notches or the points where the load is applied. For a non-uniform body the result is an average over the cross-section, so treat it as a first estimate.

Stress and pressure

Stress and pressure share units, pascals or psi, but they are different ideas. Pressure acts on a surface from the outside, while stress is the internal force per area inside a material. Wikipedia says that stress has the same dimension as pressure, and that pressure is the special case of isotropic compressive stress [2]. If you only need a unit conversion between pascals, psi, bar and megapascals, use the pressure converter, and use this tool when the force acts along a bar or a wire.

Checking your inputs

Before you trust a result, check that the force acts along the axis of the bar, that the area is the one that carries the load, and that the two lengths use the same unit. A tiny change in length is hard to measure, so a small error in ΔL gives a big error in the modulus. If your answer for a common metal is far from the values in the table, look first for a unit slip, such as millimetres entered for metres, before you suspect the material [1].

Common mistakes

  • Mixing millimetres and metres. Use one unit system for all four boxes.
  • Using the final length instead of the change. Enter ΔL, not the new length.
  • Forgetting the sign. Compression is negative.
  • Using a value above the yield point. The linear formulas stop working there.

What next

Use this often? Add Stress to your Home screen.

Frequently asked questions

What is a stress calculator?

A tool that finds axial stress, strain or Young's modulus from the force, the area and the change in length.

What is the stress formula?

σ = F ÷ A, the force divided by the cross-section area.

How do I use a young modulus calculator?

Enter the force, the area, the original length and the change in length, and the tool gives E = σ ÷ ε.

What is a typical Young's modulus for steel?

About 200 GPa for A36 steel and 68 GPa for aluminium, as approximate values.

When is the formula valid?

Only in the linear elastic range of the material, below the yield point.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools