Saved

Press the star next to a tool's name to save it.

All my tools

Speaker Crossover Calculator

Use this speaker crossover calculator to find the coil and capacitor values of a two-way passive crossover, first order, Butterworth or Linkwitz–Riley, from the frequency and impedance.

Restored your last values ·

Choose the type of crossover, enter the frequency at which you want to split the sound between the woofer and the tweeter, and the impedance of the speakers. You get the coil and capacitor values for a two-way passive crossover.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the crossover frequency and the impedance, then press Calculate.

See full result

A speaker crossover calculator finds the values of the coils and capacitors for a two-way passive crossover, which sends the low notes to the woofer and the high notes to the tweeter. Enter the crossover frequency and the impedance of the speakers, and choose a first order or second order design.

How to use the speaker crossover calculator

  1. Choose the type of crossover.
  2. Enter the crossover frequency and the impedance.
  3. Press Calculate.

What a crossover does

A crossover splits the audio signal into frequency bands, one for each driver. Passive crossovers are made of coils, capacitors and sometimes resistors placed between the amplifier and the speakers. Most audio crossovers use filters of the first to the fourth order [1]. A second-order filter is common in passive crossovers, since it balances complexity against the protection of the drivers [1].

The slope

The order of the filter sets how fast it cuts the unwanted frequencies. A first-order filter has a slope of 20 decibels per decade, or 6 decibels per octave, a second-order one has 40 decibels per decade, or 12 per octave, and a third-order one has 60 decibels per decade, 18 per octave [1]. A steeper slope protects a tweeter better from low notes, but needs more parts and shifts the phase more.

First-order values

For a first-order crossover, the reactance of the part equals the impedance of the speaker at the crossover frequency. With X_L = 2π f L and X_C = 1 ÷ (2π f C) [2], the woofer needs a series coil of L = R ÷ (2π f) and the tweeter a series capacitor of C = 1 ÷ (2π f R). For 2,500 hertz and 8 ohms, L = 0.5093 millihenries and C = 7.958 microfarads. The page states that first-order filters have a Butterworth characteristic [1].

Second-order Butterworth

For a second-order Butterworth design, the woofer has a series coil L = √2 R ÷ (2π f) and a parallel capacitor C = 1 ÷ (√2 · 2π f R), and the tweeter has a series capacitor of the same C and a parallel coil of the same L. These are standard design equations, and they are our own working. For the example, L = 0.7203 millihenries and C = 5.627 microfarads. The page says that a second-order filter can be Butterworth [1].

Linkwitz–Riley

The page says that second-order filters can be Bessel, Linkwitz–Riley or Butterworth [1]. A Linkwitz–Riley second-order design has L = R ÷ (π f) and C = 1 ÷ (π f R), which for the example give 1.0186 millihenries and 15.915 microfarads. Each driver is down by 6 decibels at the crossover frequency, so the two add up to a flat response, which is the reason for its popularity.

The 3 dB point

In a Butterworth design, each driver is down by 3 decibels at the crossover frequency. The page notes that the summing of a second-order Butterworth pair gives a peak of 3 decibels at the crossover, which is its caption's remark on the figure [1]. The Linkwitz–Riley design avoids this peak. That is a reason to choose one or the other, depending on the drivers and the room.

Choosing the frequency

The crossover frequency should be well above the resonance of the tweeter, and below the frequency at which the woofer starts to beam and become uneven. Typical values for a small two-way speaker are 2 to 3 kilohertz, a rough range of our own. Use the data sheets of the drivers. If the frequency is too low, the tweeter may be damaged by the bass.

The impedance

The calculator takes a single nominal impedance, such as 4, 6 or 8 ohms, for both the drivers. A real driver's impedance rises with the frequency, because of its voice coil, and has a peak at its resonance. This makes a crossover with fixed values work differently from the ideal. Designers often add a small network to flatten the impedance, which this calculator does not cover.

Units

The frequency is in hertz and the impedance in ohms. The coils are given in millihenries and the capacitors in microfarads. Use film capacitors rated for the audio signal, and coils with a low resistance, since the resistance of a coil adds to the impedance of the woofer. Round to the nearest standard value, and check the result by measuring.

Using the calculator

Pick the order, then enter the frequency and the impedance. Read the four values for the second-order types, or the two values for the first-order one. Build the network between the amplifier and the drivers, with the polarity as the design requires, and test it. Try different frequencies to see how the values change: doubling the frequency halves each coil and capacitor.

Example for a 4 ohm speaker

For the same 2,500 hertz crossover with 4 ohm drivers, every coil is halved and every capacitor doubled. The first-order values become 0.2546 millihenries and 15.915 microfarads. The second-order Butterworth values are 0.3601 millihenries and 11.254 microfarads. These come from our own calculations with the formulas above. The pattern is general: a lower impedance needs bigger capacitors and smaller coils.

Building the network

Solder carefully and keep the coils away from each other, as they can couple magnetically. Use air-core coils for the tweeter section, since iron cores can saturate at high power. Check the polarity of each driver, because some designs need the tweeter reversed. A test with a measurement microphone is the best way to confirm the result.

Common mistakes

  • Using the nominal impedance without checking. Real impedance varies.
  • Mixing up the coil and the capacitor. The woofer takes the coil in series.
  • Choosing too low a frequency for the tweeter. It may be damaged.
  • Using polarized capacitors. Use non-polar ones.

What next

Use this often? Add Speaker Cros to your Home screen.

Frequently asked questions

What is a speaker crossover calculator?

A tool that finds the coil and capacitor values for a speaker crossover.

What is the first-order crossover formula?

L = R ÷ (2π f) for the woofer coil, C = 1 ÷ (2π f R) for the tweeter capacitor.

What is the slope of a second-order crossover?

12 dB per octave, or 40 dB per decade.

What is a Linkwitz–Riley crossover?

A second-order design with each driver down 6 dB at the crossover, which sums to a flat response.

Why does the real impedance matter?

A driver's impedance changes with frequency, which shifts the real crossover point.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools