A snow load calculator estimates the weight of the snow lying on a roof. Enter the flat size of the roof, its pitch, the depth of the snow and the type of snow, and the calculator gives the snow load, which is the weight per area, and the total weight on the roof. It uses depth times density, with snow weights chosen to match FEMA's published figures. It runs in your browser and nothing you enter is sent anywhere.
What snow load is
The snow load is the pressure exerted by the snow, with units such as pounds per square foot or kilonewtons per square metre. It is found by multiplying the depth of the snow by its density. The weight of the snow on the whole roof is then the roof surface area times the snow load. Snow weighs more when it is wet, packed or frozen, so the same depth can give very different loads. FEMA says that 1 foot of fresh snow weighs from 3 pounds per square foot for light, dry snow to 21 for wet, heavy snow.[1]
How to use the snow load calculator
- Choose US or Metric units.
- Enter the length and width of the flat area the roof covers.
- Enter the pitch, as rise per 12 or as an angle.
- Enter the snow depth, choose the snow type and press Find snow load.
The snow densities
The calculator uses the following snow densities. Fresh snow is 60 kilograms per cubic metre, or 3.75 pounds per cubic foot. Damp fresh snow is 110, or 6.87. Settled snow is 250, or 15.61. Wind-packed snow is 375, or 23.41. Very wet snow is 750, or 46.82. Ice is 917, or 57.25, which is over 15 times the density of fresh snow. FEMA gives about 57 pounds per square foot for 1 foot of ice, so the ice figure matches, and the fresh and damp fresh figures fall inside FEMA's range for fresh snow.[1] The settled, wind-packed and very wet figures are our own estimates, since snow density varies with place and weather. Wikipedia notes that a snowpack may settle until its density is about 30 percent of water.[2]
The formulas
The snow load is the depth times the density, so 12 inches of fresh snow, which is one foot, gives 3.75 pounds per square foot. The weight of snow on the roof is the roof length times the width, divided by the cosine of the pitch angle, times the snow load. This is our own working. The division by the cosine turns the flat area under the roof into the real area of the sloping surface. A pitch given as rise per 12 is turned into an angle with the arctangent of the rise divided by 12.
Worked examples
A flat roof of 30 by 20 feet has an area of 600 square feet. With 12 inches of fresh snow, the load is 3.75 pounds per square foot, and the snow weighs 2,250 pounds. If the roof has a pitch of 6:12, which is an angle of 26.6 degrees, the surface area is about 671 square feet, and the snow weighs about 2,516 pounds. In metric units, 30 centimetres of fresh snow on a flat roof of 10 by 6 metres gives a load of 18 kilograms per square metre and a weight of 1,080 kilograms.
What the roof can carry
This calculator does not compare the snow weight with what your roof can carry. It gives only the weight of the snow, because the permissible load depends on the building, its age, its exposure and the local code. FEMA says that the design snow load can be found on the construction drawings, and that if there are none, you should retain a licensed design professional to determine the structural capacity.[1] Ask a structural engineer or check your local building code for your roof's limit.
Safety
The numbers here are only an approximation. FEMA warns that attempting to remove snow from a roof is more often hazardous than beneficial, posing a risk to people and to the roofing structure.[1] It recommends that removal be done by a licensed, insured roofing contractor, following rooftop safety rules and using fall protection,[1] and that if there is any concern that the snow may cause a collapse, all removal should stop and the building should be evacuated.[1] If you see warning signs, contact a qualified design professional such as a structural engineer.[1]
Reading the result
The calculator shows the snow load as a weight per area, the surface area of the roof, the roof angle and the total weight of the snow. In metric units it also shows the load in kilonewtons per square metre, a unit that engineers use.
Why the type of snow matters
Depth alone says little about weight. A foot of fresh, dry snow is light, but the same foot after rain has fallen on it can weigh many times more. The densities in the table show the range: fresh snow is 3.75 pounds per cubic foot, very wet snow is 46.82, and ice is 57.25. A thin layer of ice can weigh as much as a deep layer of new snow. Choose the type that matches what you see, and when you are unsure, try two types to see the range.
Measuring the depth
Measure the depth at several places. Snow drifts against walls, chimneys and higher roof sections, so the load is not even, and an uneven load is a greater risk to the roof than an even one.[1] For a drift, measure its depth and enter it with a smaller roof area.
Common mistakes
- Using the roof's sloped length. Enter the flat plan size.
- Choosing the wrong snow type. Wet snow is many times heavier than fresh snow.
- Taking the result as a safe limit. It is only the weight of the snow.
- Measuring the depth at one spot. Drifts make it deeper in places.
What next
Use this often? Add Snow Load to your Home screen.
Frequently asked questions
What is a snow load calculator?
A tool that estimates how much the snow on a roof weighs from the roof size, pitch, snow depth and type of snow.
How do you calculate snow load?
Multiply the depth of the snow by its density. The weight on the roof is the roof surface area times that load.
How much does snow weigh?
The calculator uses fresh snow at 60 kg/m³ (3.75 lb/ft³), settled snow 250 (15.61), very wet snow 750 (46.82) and ice 917 (57.25). FEMA reports 3 to 21 pounds per square foot for each foot of fresh snow and about 57 for ice.
Does it tell me if my roof is safe?
No. It gives only the weight of the snow. The roof's limit depends on the building and the local code, so ask a structural engineer.
When should I remove snow from a roof?
FEMA says removal is prudent when the load is close to the roof's capacity, and that it should be done by a licensed, insured roofing contractor. If you see signs of damage, leave the building and call a structural engineer.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.