A sled calculator finds the force that you need to pull a sled, with friction, on level ground or up a slope. You give the mass, the slope and a friction coefficient, and optionally the angle of the rope, and it returns the pulling force in newtons and pounds-force.
How to use the sled calculator
- Choose US or metric units.
- Enter the mass of the sled and its load, and the friction coefficient.
- Add the slope angle and, if you wish, the rope angle.
- Press Calculate.
The forces on a sled
A sled on a slope has its weight W = m g acting downwards, a normal force from the snow at right angles to the surface, and friction along the surface. The Wikipedia article on the inclined plane writes the equilibrium along the plane and across it, with the friction equal to the normal force times the coefficient of friction [1]. The calculator applies these balances with g = 9.80665 metres per second squared.
Pulling up a slope
To move the load up at a constant speed, the pull must balance the component of weight along the slope and the friction. The article gives the uphill balance, which rearranges to F = W (sin θ + μ cos θ) when the pull is parallel to the slope [1]. That rearrangement is our own working from the equation quoted there. For 20 kilograms, a 10 degree slope and μ = 0.1, the pull is 53.4 newtons.
Level ground
On level ground the angle is zero, and the formula becomes F = μ W. The same 20 kilogram sled, with a weight of 196.1 newtons and μ = 0.1, needs 19.6 newtons, about 4.4 pounds-force. This is the value shown when you leave the slope blank. In the real world the force needed to start the sled moving can be higher than that to keep it going, because the coefficient of static friction is usually larger than that of kinetic friction [2]. This tool uses a single coefficient for both.
The rope angle
A rope that rises above the slope pulls partly upward, which lightens the load on the snow and reduces friction, but the part of the pull that acts along the slope is smaller. Our working gives F = W (sin θ + μ cos θ) ÷ (cos φ + μ sin φ), where φ is the angle of the rope. The calculator also finds the angle with the smallest pull, which is arctan μ. For μ = 0.1 that is 5.7 degrees.
Choosing the friction coefficient
The coefficient depends on the runners and on the snow, so you must enter your own value. Wikipedia's table of friction coefficients gives low values for ice on ice and for steel on ice [2], but a sled on snow can differ a lot. Measure a real value by pulling the sled with a spring scale.
Will it slide by itself?
The angle of friction is the angle whose tangent is the coefficient of friction, and it is the largest slope on which a load can rest without sliding [1]. If the slope is steeper, the sled slides down. Down a slope, friction opposes the motion, so the acceleration is g (sin θ − μ cos θ). This is our own working from the force balance above.
Why the sign matters
With a plus sign, more friction would make the sled faster, which is not physical. With the minus sign, the acceleration for μ = 0.1 on a 20 degree slope is 2.43 metres per second squared, and no friction at all gives g sin θ.
Speed and safety
Sledding can be dangerous on a hill. This calculator is about the pulling force, not about how fast a sled goes, so it does not give a speed. For a hill, check the run-out at the bottom, avoid trees, roads and water, and let an adult supervise young children.
Units
In US mode the mass is in pounds and the result is given in newtons and pounds-force. In metric mode the mass is in kilograms. The conversion of pounds to kilograms uses 0.45359237, and one pound-force is 4.4482216 newtons. The slope and rope angles are in degrees from the horizontal and from the slope. A friction coefficient has no unit.
Limits
The model assumes a constant coefficient of friction, a rope that is straight, a steady speed and a flat slope. It ignores air drag, soft snow that the sled ploughs through, and the effect of speed on friction. A heavy load on deep snow needs more force than the formula says. Treat the result as an estimate, and use a spring scale when you need a firm number.
A rope-angle example
Take our own example of a 20 kilogram sled on a 10 degree slope with μ = 0.1. The weight is 20 × 9.80665 = 196.13 newtons. With the pull parallel to the slope, F = 196.13 × (sin 10° + 0.1 × cos 10°), which is about 53.4 newtons [1].
Now raise the rope to 5.7 degrees, the angle whose tangent is 0.1. The formula above gives 196.13 × 0.2721 ÷ (cos 5.7° + 0.1 × sin 5.7°), which is about 53.1 newtons. The saving is only about 0.3 newtons, or half of one percent.
The lesson is that a rope at the best angle helps a little, but it does not change the result much when the friction coefficient is low. The slope and the mass matter far more. Try a few rope angles in the calculator to see how flat the curve is near its minimum.
Common mistakes
- Entering the weight instead of the mass. Enter mass; the tool applies g.
- Guessing a very low friction coefficient. Measure it if you can.
- Using a rope angle that lifts the sled. The tool will warn you.
- Forgetting that a slope above the friction angle slides by itself. Read the slope note.
What next
Use this often? Add Sled to your Home screen.
Frequently asked questions
What is a sled calculator?
A tool that finds the force to pull a sled with friction on level ground or a slope.
What is the formula for the pull up a slope?
F equals weight times sine of the angle plus the friction coefficient times cosine of the angle, with the rope parallel.
What friction coefficient should I use for a sled?
This tool holds no table of values, so measure your own with a spring scale.
What is the best rope angle for pulling a sled?
The angle whose tangent equals the friction coefficient, above the slope, gives the smallest pull.
When does a sled slide down by itself?
When the slope is steeper than the angle of friction, whose tangent is the friction coefficient.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.