A ramp slope calculator turns the rise and the run of a ramp into its slope, expressed as a ratio, a percent grade and an angle. It can also give the run you need for a given rise at the 1:12 slope used for wheelchair ramps, and it checks your ramp against the ADA limits.
How to use the ramp slope calculator
- Choose US or metric units.
- Choose what you know.
- Enter the rise and the run, or the rise and a ratio.
- Press Calculate.
Slope, rise and run
The slope of an inclined plane is the difference in height between its two ends, the rise, divided by its horizontal length, the run [3]. The angle of the plane is the inverse tangent of that ratio, θ = tan⁻¹(rise ÷ run) [3]. The percent grade is the slope times 100, which is our own simple conversion. A ramp with a rise of 1 and a run of 12 has a slope of 1/12, a grade of 8.33 percent and an angle of 4.76 degrees.
The ADA limit
The ADA 2010 Standards say that ramp runs shall have a running slope not steeper than 1:12 [1]. The rise for any ramp run shall be 30 inches, or 760 millimetres, maximum, and landings shall be at least 60 inches, or 1,525 millimetres, long [1]. For existing sites, the standards allow steeper slopes where space is limited, with a smaller maximum rise: steeper than 1:12 up to 1:10 gets a rise of 6 inches, and steeper than 1:10 up to 1:8 gets 3 inches, while anything steeper than 1:8 is prohibited [1].
Run for a given rise
The page on wheelchair ramps puts the 1:12 rule in simple terms: a slope of no more than 1:12 works out to 1 foot of ramp for each inch of rise [2]. Its example is a 20-inch rise, which needs at least 20 feet of ramp [2]. That length is the horizontal run. Enter a rise of 20 inches and the calculator gives a run of 240 inches, or 20 feet, and a sloped length of about 240.8 inches.
Sloped length
The surface of the ramp is a little longer than its run, by the Pythagorean theorem: the length is the square root of the run squared plus the rise squared. For a gentle slope the difference is small. For the 20-inch rise the extra is under an inch. The calculator shows both, since the run is what you measure on the ground and the length is the amount of decking.
Other codes
The ADA limit is not universal. The page notes that the UK uses 1:12, that Australia's national construction code uses 1 in 8, and that South Africa allows 1:10 when the rise is under 400 millimetres [2]. Check the code that applies to your building. The calculator lets you enter any ratio, so you can see the length that other limits give.
Worked examples
A porch 30 inches above the ground needs a run of at least 360 inches, or 30 feet, at 1:12, the longest single run the ADA allows. A step of 7 inches needs 84 inches, or 7 feet. A ramp with a 30 inch rise and only 200 inches of run has a slope of about 1:6.7, steeper than the limit. A metric ramp with a rise of 50 centimetres at 1:10 needs 5 metres of run. These are our own calculations.
Landings
When a ramp climbs more than 30 inches, it needs landings between runs. Each landing must be at least 60 inches long [1], so the total space needed is the sum of the runs and the landings. The calculator flags a rise above the limit with a reminder to add a landing. It does not plan the full layout, so sketch the path before you build.
Practical tips
Aim for a gentler slope than the limit if you have the room, since 1:12 is steep for many users. Measure the rise from the finished floor to the finished surface at the top. Allow for the thickness of the ramp surface. Keep the surface firm and slip-resistant, and add the handrails and edge protection that your code requires.
Choosing the slope
The 1:12 slope is a maximum, not a target. Users with limited strength may find a slope of 1:12 tiring over a long run, and a gentler slope such as 1:16 or 1:20 is more comfortable if there is room. Enter the ratio in the second box to see how much longer the ramp becomes: at 1:20 a rise of 20 inches needs 400 inches, or 33 feet, of run.
Converting between forms
People describe slopes in several ways. A ratio of 1:12, a grade of 8.33 percent and an angle of 4.76 degrees all describe the same ramp. The calculator shows all three so that you can compare with a code that uses a different form, or with a manufacturer's description of a ramp system.
Common mistakes
- Using the sloped length as the run. The ratio uses the horizontal run.
- Mixing inches and feet. Enter rise and run in the same unit.
- Forgetting landings. A rise over 30 inches needs a landing.
- Assuming 1:12 is the same everywhere. Codes differ by country.
What next
Use this often? Add Ramp Slope to your Home screen.
Frequently asked questions
What is a ramp slope calculator?
A tool that turns the rise and run of a ramp into a slope ratio, percent grade and angle.
What is the ADA ramp slope?
Not steeper than 1:12, with a maximum rise of 30 inches for one run.
How long must a ramp be for a given rise?
At 1:12 it needs 1 foot of run for each inch of rise. A 20 inch rise needs 20 feet.
How do I convert a slope to a percent grade?
Divide the rise by the run and multiply by 100. A 1:12 slope is 8.33 percent.
Do I need a landing?
Yes, for a rise above 30 inches, with each landing at least 60 inches long.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.