Saved

Press the star next to a tool's name to save it.

All my tools

Section Modulus Calculator

Use this section modulus calculator to find S = I ÷ c for a rectangle, a circle, a pipe or a box section, with the second moment of area and the peak bending stress.

Restored your last values ·

Choose the shape and the units, then enter the dimensions. Height is measured in the direction of the bending. You get the elastic section modulus S, the second moment of area I and the distance c to the outer fibre. Add a bending moment to see the peak stress.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose a shape, enter its dimensions and press Calculate.

See full result

A section modulus calculator finds the elastic section modulus S of a beam cross-section: how much bending moment the shape can resist for a given stress. Pick a rectangle, a circle, a pipe or a box section, enter the dimensions in inches or millimetres, and get S, the second moment of area, and the peak bending stress for a moment you enter.

How to use the section modulus calculator

  1. Choose the shape and the units.
  2. Enter the dimensions. The height is the size in the direction of the bending.
  3. Add a bending moment if you want the peak stress.
  4. Press Calculate.

What the section modulus is

The elastic section modulus is defined as S = I ÷ c, where I is the second moment of area about the neutral axis and c is the distance from that axis to the most extreme fibre [1]. It has the unit of length cubed, such as mm³ or in³. A larger S means that the shape is stiffer against bending stress, so a beam with a bigger section modulus carries a bigger moment for the same stress.

From section modulus to stress

The peak bending stress in a beam is the moment divided by the section modulus, σ = M ÷ S, so you can find the stress from a known moment, or the moment a shape can take for a chosen stress. Wikipedia's article on bending writes the flexure formula as σ = M ÷ W, where W = I ÷ y is the resistance moment, which is the section modulus [2]. Wikipedia gives the yield moment as the section modulus times the yield strength, My = S × σy [1]. The calculator shows the stress when you enter a bending moment.

Rectangle

For a solid rectangle of width b and height h, S = b h² ÷ 6, from I = b h³ ÷ 12 and c = h ÷ 2 [1]. With b = 100 mm and h = 200 mm, S = 100 × 200² ÷ 6 = 666,667 mm³. The height is squared, so doubling the depth of a beam makes it four times stronger in bending, while doubling the width only doubles it. This is why beams are placed on edge.

Solid circle

For a solid circle of diameter d, S = π d³ ÷ 32 [1]. In terms of the radius R it is (π ÷ 4) R³, which is the same thing. For a diameter of 100 millimetres (radius 50), S = 98,175 mm³. A shaft or a round bar has a smaller modulus than a square bar of the same width, since it has less material far from the axis.

Hollow circle or pipe

For a pipe with outer diameter D and inner diameter d, S = π (D⁴ − d⁴) ÷ (32 D) [1]. In terms of the radii, take a pipe of outer radius 50 mm and inner radius 40 mm: S is about 57,962 mm³. Enter a diameter of 100 and an inner diameter of 80 to reproduce it. A pipe keeps most of the strength of a solid bar with much less material.

Hollow rectangle

For a box section with outer size B by H and inner size b by h, S = (B H³ − b h³) ÷ (6 H), which Wikipedia writes as B H² ÷ 6 − b h³ ÷ (6 H) [1]. For an outer 100 by 200 millimetres and an inner 60 by 160, S = 461,867 mm³. This is our own example. The inner size must be smaller than the outer size in both directions, and the calculator checks it.

Elastic and plastic

The elastic modulus applies while the stress and strain are proportional. The plastic modulus Z is used when the whole section has yielded, and for a rectangle Z = b h² ÷ 4, so the ratio Z ÷ S is 1.5 [1]. This calculator gives the elastic value only. The plastic values and I-beam sections are not included here.

Units

In US mode, enter lengths in inches and the moment in pound-force inches. S is shown in cubic inches, with the millimetre conversion, and the stress in psi. In metric mode, enter millimetres and newton metres. S is shown in cubic millimetres and the stress in megapascals, since 1 N per square millimetre is 1 MPa. The factor between inches and millimetres is 25.4, so the cubic factor is 16,387.

Where the formulas stop

The formulas are for a section that bends about the horizontal axis through its centre, which is the neutral axis of a symmetric shape. They do not include shear, buckling, holes, welds or stress concentrations. For an unsymmetrical shape, the distances to the top and the bottom fibres differ, and there are two different moduli. This calculator is only for the symmetric shapes listed.

Using the calculator

Pick the shape and the units, enter the dimensions and, if you know it, the bending moment. Read S and the stress, then compare shapes. Try the same area as a square, a round bar and a pipe, and see how the hollow shape gives more S for the area. The result is a first estimate for study and checking, and a real beam needs a proper design check.

Comparing shapes for the same material

The section modulus is the tool for choosing between shapes. A square bar of 100 millimetres has S = 166,667 mm³, while a solid round bar of the same 100 millimetre width has only 98,175 mm³, so the round bar carries about 59 per cent of the moment of the square one, but it also has less material. A pipe or a box section scores much higher than a solid bar, since its material lies far from the neutral axis, where it helps the most in bending. These comparisons are our own working from the formulas above, and they are the reason that beams are made as I-sections and tubes.

Common mistakes

  • Using the wrong height. Use the size along the direction of the bending.
  • Mixing inches and millimetres. Pick one unit system.
  • Mixing up S and I. S is I divided by c.
  • Entering an inner size larger than the outer. The hollow must fit inside.

What next

Use this often? Add Section Modu to your Home screen.

Frequently asked questions

What is a section modulus calculator?

A tool that finds S = I ÷ c for a cross-section, the measure of its resistance to bending.

What is the section modulus of a rectangle?

S = b h² ÷ 6, with b the width and h the height in the direction of bending.

How do I get bending stress from the section modulus?

Divide the bending moment by S: σ = M ÷ S.

What is the difference between elastic and plastic section modulus?

The plastic modulus Z applies after the whole section has yielded; for a rectangle Z is 1.5 times S.

What units does the section modulus have?

Length cubed, such as mm³ or in³.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools