A factor of safety calculator finds the ratio of the strength of a part to the stress or load that it carries, and the margin of safety. Choose an application, or enter a required design factor, to see whether the part passes. It works with stresses, loads or any other pair of values in the same unit.
How to use the factor of safety calculator
- Enter the strength and the applied stress or load.
- Choose an application or enter a design factor.
- Press Calculate.
The factor of safety
The page gives two meanings of the factor of safety: a calculated, or realized, ratio of the absolute strength of the structure to the applied load, and a required design factor set by a code, a standard or a contract [1]. For a simple case, the factor is the yield stress divided by the working stress [1]. A factor of 1 supports only the design load, and a factor of 2 will fail at twice the design load [1].
The margin of safety
The margin of safety is the factor of safety minus one, in the capability form: failure load ÷ design load − 1 [1]. A part with a factor of 2.5 has a margin of 1.5, or 150 percent. The page notes that it is sometimes, but not often, given as a percentage [1]. The calculator shows it both as a number and as a percentage.
The requirement form
When a design factor is required, the margin is written as failure load ÷ (design load × design factor) − 1, which equals the realized factor ÷ the design factor − 1 [1]. A margin of zero or more passes [1]. For a part with a factor of 2.5 and a required design factor of 2, the margin is 0.25, so it passes. With a required factor of 3.5, the margin is −0.29, and it fails.
The page's example
The page gives the example of a part with a required design factor of 3 and a margin of 1, which has a realized factor of 6 [1]. A margin of 0 would pass at a factor of 3 [1]. You can check this in the calculator: enter 600 for the strength, 100 for the load and choose a design factor of 3, which gives a margin of 1.
Typical design factors
The page gives typical values. Buildings use about 2.0 for each member, pressure vessels 3.5 to 4.0 and automobiles 3.0 [1]. For aircraft and spacecraft, it gives 1.2 to 4.0 depending on the application and the materials, and says that a usually applied safety factor is 1.5, with 2.0 for a pressurized fuselage and often 1.25 for main landing gear [1]. The calculator has values for four of these, and you can enter any other.
Critical parts
For critical components, where a failure could cause financial loss, serious injury or death, the page says that factors of four or higher, often ten, are used, though that statement lacks a citation [1]. For non-critical parts the factor is generally about two [1]. Ductile metals tend to need lower factors, and brittle materials higher ones [1]. Choose the figure that your standard sets.
Yield and ultimate
For ductile materials, both the yield and the ultimate strength should be checked, but for brittle materials the ultimate check is usually enough [1]. Enter the strength that is relevant to your failure mode: the yield stress for a part that must not deform, or the ultimate stress for a part that must not break. Use the same kind of figure for the stress or load.
Fatigue
The page also points out that cyclic loading can cause fatigue failure below the yield stress [1]. A static factor of safety does not cover this, so a part under repeated loads needs a separate fatigue analysis. The calculator gives only the ratio of two numbers that you supply, and it cannot know whether the loading is steady or cyclic.
Units
The strength and the load can be in any unit, as long as both are the same: megapascals, psi, newtons or tonnes. The calculator takes the ratio, so the units cancel. If the strength is a stress and the load is a force, convert one to the other first, using the cross-sectional area of the part.
Using the calculator
Enter the strength and the stress. Read the factor and the margin. To compare with a requirement, pick the application, or enter your own factor, and read whether the part passes. If it fails, increase the section, use a stronger material or reduce the load, and try again.
Choosing a stricter factor
If the failure of a part could be costly or dangerous, the design factor is often raised, and the tests and inspection are increased as well. Compare the result with the margin that you need, not only with zero. A part with a margin of 0.05 passes on paper, but it has little room for errors in the load, the strength or the way that the part is made.
Common mistakes
- Using different units for the strength and the load. Both must match.
- Confusing the factor with the margin. The margin is the factor minus one.
- Ignoring fatigue. Cyclic loads need another check.
- Using a typical factor instead of the code. The code sets the factor.
What next
Use this often? Add Factor of Sa to your Home screen.
Frequently asked questions
What is a factor of safety calculator?
A tool that finds the ratio of the strength of a part to the load on it.
What is the factor of safety formula?
FoS = strength ÷ applied stress, for example yield stress ÷ working stress.
What is the margin of safety?
MoS = FoS − 1, or FoS ÷ design factor − 1 when a design factor is required.
What are typical design factors?
About 2 for buildings, 3 for automobiles, 3.5 to 4 for pressure vessels and 1.5 for aircraft.
Does a factor of 1 mean a safe design?
No. It supports only the design load, with no margin.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.