This sealant calculator works out how many cartridges of caulk or sealant you need to fill a joint. Enter the joint's width, depth and total length, choose the cartridge size, and the sealant calculator gives the number of cartridges, the volume of sealant, and how far one cartridge goes.
How to use the sealant calculator
- Choose US or metric units. US (inches, feet and fluid ounces) is the default.
- Enter the joint width and depth.
- Enter the total length of all the joints you'll seal.
- Choose the cartridge size and add a waste allowance, then press Calculate.
What is caulk or sealant?
According to Wikipedia, caulk is a material used to seal joints or seams against leakage; modern caulks are flexible sealing compounds that keep out water, air, dust and insects. It notes that when a joint material is silicone-based, it's considered a sealant rather than caulk. Both are commonly sold in rigid cylindrical cartridges that fit a caulking gun.
How the calculator works
A sealant joint is roughly a rectangle in cross-section, so the volume of sealant is:
volume = width × depth × length
The calculator works in millimeters and meters, where a joint 1 mm wide, 1 mm deep and 1 m long holds 1 mL. It adds your waste allowance, divides by the cartridge volume and rounds up. A US fluid ounce is 29.57 mL, so a 10.1 fl oz cartridge holds about 299 mL, or 18.2 cubic inches.
Worked example
Sealing 100 feet of joints 1/4 inch wide and 1/4 inch deep needs about 1,229 mL, or 41.6 fluid ounces, of sealant. One 10.1 fl oz cartridge fills about 24.3 feet of that joint, so you need 5 cartridges. With a 10% waste allowance it's still 5, but a joint 3/8 inch wide and 1/4 inch deep would need 7.
Backer rod
For deeper joints, a foam backer rod is pressed in first to set the sealant's depth, so you don't waste sealant filling the whole gap. Wikipedia explains that backer rod sets the thickness of the sealant, helps form an hourglass shape, and acts as a bond breaker so the sealant sticks only to the two sides of the joint. Closed-cell backer rod shouldn't be compressed more than 25%, while open-cell rod should be compressed 25% to 75%. Enter the depth from the surface to the backer rod.
Reading the results
The big number is the number of cartridges to buy. The table shows the total sealant volume, the same volume in cubic inches, and how many feet or meters of joint one cartridge fills.
Bead sizes and coverage
Coverage falls quickly as the bead gets bigger, because the volume depends on both width and depth. Doubling both the width and depth of a joint needs four times as much sealant, so a cartridge that seals 24 feet of a 1/4-inch joint seals only about 6 feet of a 1/2-inch joint. Measure your joints before buying.
Cartridge sizes
Sealants come in several cartridge sizes. The 10.1 fluid ounce cartridge, about 300 mL, is the familiar size for a standard caulking gun. Larger 20 and 28 fluid ounce cartridges hold about 590 and 830 mL and need a larger gun, and some sealants come in foil sausage packs measured in milliliters. Choose Other size to enter any cartridge, in fluid ounces or milliliters.
Metric joints
Choose metric to enter the joint width and depth in millimeters and the length in meters. A 6 × 6 mm joint 30 meters long holds about 1,080 mL of sealant, so it needs four 300 mL cartridges. Each cartridge fills about 8.3 meters of that joint.
Adding up joints
For a job with joints of different sizes, run the calculator for each size and add the results. Measure the total length of each kind of joint, such as around windows, along baseboards or at the bottom of siding. A tape measure and a quick sketch of each wall help you avoid missing any.
Waste allowance
Some sealant is always left in the nozzle and cartridge, and tooling the bead removes a little. Adding a waste allowance of a few percent and rounding up to whole cartridges makes it less likely you'll run out partway through a joint.
Getting a good joint
Sealant works best in a clean, dry joint with sound edges. Remove old sealant and loose material, insert backer rod where the joint is deep, and apply the sealant in one steady pass. Tooling the bead with a smooth tool presses the sealant against both sides of the joint and gives a neat finish. Check the sealant maker's instructions for the joint sizes and temperatures it's meant for.
Store opened cartridges with the nozzle capped so leftover sealant stays usable for touch-ups later.
Common mistakes
- Guessing the joint size. Measure width and depth.
- Filling deep gaps with sealant. Use backer rod first.
- Buying the exact amount. Nozzle waste and tooling use some.
- Mixing cartridge sizes. Check the label for the volume.
Tips
- Cut the nozzle to match the bead width.
- Clean and dry joints before sealing.
- Tool the bead soon after applying it.
What next
Use this often? Add Sealant to your Home screen.
Frequently asked questions
How does a sealant calculator work?
It multiplies the joint width, depth and length to get the sealant volume, then divides by the cartridge volume.
How far does a 10.1 oz tube of caulk go?
About 24 feet of a 1/4 × 1/4-inch joint, before waste.
How many caulk tubes do I need for 100 feet?
About 5 cartridges of 10.1 fl oz for a 1/4 × 1/4-inch joint.
What is backer rod for?
It sets the sealant depth, shapes the bead and stops the sealant sticking to the back of the joint.
What is the difference between caulk and sealant?
Wikipedia notes that silicone-based joint materials are considered sealants rather than caulk.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.