Saved

Press the star next to a tool's name to save it.

All my tools

RF Unit Converter

Use this RF unit converter to change a signal level between dBm, dBW, milliwatts, watts, microwatts, volts rms and dBµV for 50, 75 or any impedance.

Restored your last values ·

Ω

Enter a value in dBm, dBW, milliwatts, watts, microwatts, volts rms or dBµV, and choose the impedance of the circuit, usually 50 ohms. You get the same signal in all the other units. The voltage conversions need the impedance, and the power ones do not.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose the unit, enter a value, then press Convert.

See full result

An RF unit converter changes a signal level between the units that radio engineers use: dBm, dBW, milliwatts, watts, microwatts, volts and dBµV. Enter a level in any one of them, give the impedance of the circuit, usually 50 ohms, and you get all the others. It is useful for transmitters, receivers, antennas, cables and test equipment. It runs in your browser.

How to use the RF unit converter

  1. Choose the unit of your value.
  2. Enter the value, and the impedance if it is not 50 ohms.
  3. Press Convert.

What dBm is

The Wikipedia article on dBm says that to express a power P in milliwatts as x in dBm, you use x = 10 log₁₀ (P ÷ 1 mW), and the inverse is P = 1 mW × 10^(x ÷ 10).[1] So 0 dBm is 1 milliwatt, and the page's table lists 20 dBm as 100 milliwatts, 30 dBm as 1 watt, 40 dBm as 10 watts and 60 dBm as 1 kilowatt. Going down, −10 dBm is 100 microwatts, −30 dBm is 1 microwatt and −60 dBm is 1 nanowatt.[1] The page notes that a rise of 3 dBm roughly doubles the power, 10 dB is ten times and 20 dB is a hundred times.[1]

dBW and watts

The decibel in dBW is measured against one watt, and not against one milliwatt.[1] Since 1 watt is 1,000 milliwatts, which is 30 dB above 1 milliwatt, a level in dBW is 30 less than the same level in dBm. This follows from the definitions, as the pages do not state it in the part that we read. So 30 dBm is 0 dBW, and 0 dBm is −30 dBW. The calculator also shows the power in watts, with the best prefix, from kilowatts down to zeptowatts. The page lists thermal noise at about −174 dBm in one hertz, which the calculator shows as about 4 zeptowatts.[1]

The general decibel

The article on the decibel defines the level of a power ratio as 10 log₁₀ (P ÷ P₀), and the level of a root-power quantity, such as voltage, as 20 log₁₀ (F ÷ F₀). It notes that a change of a factor of two in power is approximately 3 dB, and that a doubling of voltage is commonly described as 6 dB.[2] These are the rules behind all the conversions.

From power to volts

The voltage across a resistance follows from the power, V = √(P × R), where P is in watts and R in ohms. This is standard electrical theory, and we apply it ourselves. The dBm page confirms the sizes: 0 dBm is about 0.224 volts in 50 ohms, which is the usual radio impedance, and 0.775 volts in 600 ohms, which was the standard in audio.[1] The calculator gives the rms voltage, the peak voltage, which is √2 times larger for a sine wave, and the peak-to-peak voltage, which is twice that. For 0 dBm into 50 ohms the values are 0.2236 volts rms, 0.3162 volts peak and 0.6325 volts peak to peak.

dBµV

Receivers and cable systems often give a level in dBµV, which is 20 log₁₀ of the voltage divided by one microvolt. The pages do not define this unit in the parts that we read, so the calculator uses the standard definition. In 50 ohms, 0 dBm is 106.99 dBµV, so dBµV is about dBm plus 107. In 75 ohms the offset is about 108.75, the value that cable engineers use. The conversion needs the impedance, so choose the right one.

Worked examples

A transmitter that puts out 5 watts is 37 dBm, which is 7 dBW. A receiver that needs −90 dBm at its input has a signal of 1 picowatt, which is a voltage of about 7 microvolts across 50 ohms. A 1 microvolt signal across 50 ohms is 0 dBµV and −107 dBm. The thermal noise of −174 dBm per hertz is why very weak signals are hard to receive. The calculator does each of these conversions, and shows the power in a unit that is easy to read, so that you do not have to count the zeros of a very small number by hand.

Adding and subtracting levels

Decibels turn multiplication into addition. If a signal at 10 dBm goes through an amplifier with 20 dB of gain and a cable with 3 dB of loss, the level at the end is 10 + 20 − 3 = 27 dBm, which is 500 milliwatts. This is why engineers work in decibels, because a chain of gains and losses is a simple sum. You cannot add two levels in dBm directly, though. Two equal signals of 0 dBm together give 3 dBm, as the powers add. Use the calculator to convert to watts, add them there, and convert back.

Choosing the impedance

Most radio and test equipment is 50 ohms, and cable television and video use 75 ohms. Some older audio gear used 600 ohms, which is where the figure of 0.775 volts for 0 dBm comes from. Use the impedance of the system that you are measuring, because the same power gives a different voltage in each.

Common mistakes

  • Mixing up dBm and dBW. They differ by 30 dB.
  • Using 10 log for voltage. Voltage uses 20 log.
  • Forgetting the impedance. Volts depend on it, power does not.
  • Adding dBm values. Add the powers, or add dB gains to a dBm level.

What next

Use this often? Add RF Unit to your Home screen.

Frequently asked questions

What is an RF unit converter?

A tool that changes a signal level between dBm, dBW, watts, volts and dBµV, given the impedance of the circuit.

How do I convert dBm to watts?

P = 1 mW × 10^(dBm ÷ 10). 30 dBm is 1 W, and 0 dBm is 1 mW.

How do I convert dBm to volts?

V rms = √(P × R). 0 dBm in 50 ohms is about 0.224 V rms.

What is the difference between dBm and dBW?

dBm is relative to 1 milliwatt and dBW to 1 watt, so dBm = dBW + 30.

How many dB double the power?

About 3 dB doubles the power, 10 dB is ten times and 20 dB is a hundred times.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools