Saved

Press the star next to a tool's name to save it.

All my tools

Pi Attenuator Calculator

Use this pi attenuator calculator to find the shunt and series resistor values of a symmetric pi pad for a wanted attenuation in dB at 50, 75 or any ohms.

Restored your last values ·

dB
Ω

Enter the attenuation that you want in decibels, and the impedance of the system, such as 50 or 75 ohms. You get the two equal shunt resistors and the one series resistor of a symmetric pi pad, with the voltage and power ratios.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the attenuation and the impedance, then press Calculate.

See full result

A pi attenuator calculator gives the three resistors of a symmetric pi pad, the attenuator that is shaped like the Greek letter π, with two shunt resistors to ground and one series resistor between them. Enter the attenuation in decibels and the impedance of your system, and you get the values, together with the voltage and power ratios and a check of the input impedance. It is used in radio, audio and test equipment to lower a signal level without upsetting the match. It runs in your browser.

How to use the pi attenuator calculator

  1. Enter the attenuation in decibels.
  2. Enter the impedance of the source and the load, such as 50 or 75 ohms.
  3. Press Calculate.
  4. Build the pad with the two shunt resistors and the series resistor.

Attenuation in decibels

The Wikipedia article on attenuators defines the loss of a pad as 10 log₁₀ (Pin ÷ Pout), and states that when the source and the load have the same impedance, it is also 20 log₁₀ (Vin ÷ Vout).[1] It lists the usual figures: 3 dB halves the power, 6 dB cuts it to a quarter, 10 dB to a tenth and 20 dB to a hundredth, and with equal impedances the voltage ratio is the square root of the power ratio, so a 6 dB pad halves the voltage.[1] The calculator shows both ratios. For 20 dB, the voltage ratio is 10 to 1 and the power ratio is 100 to 1.

The pi pad formulas

The page writes the shared quantity A = 10^(−Loss ÷ 20), the voltage ratio at the output, and gives the symmetric pi pad with equal shunt resistors Rx = Ry = Zs × (1 + A) ÷ (1 − A).[1] The series resistor of the pad is not clear in the text of the page that we could read, so we worked it out ourselves. With K = 1 ÷ A, which is the voltage ratio 10^(dB ÷ 20), the shunt resistors are Z × (K + 1) ÷ (K − 1) and the series resistor is Z × (K² − 1) ÷ (2K). The shunt formula is the same as the page's. As a check, the calculator works out the impedance that you see looking into the finished pad when it is terminated by the load, and it comes to the design impedance, which proves that the three values match.

Worked values

For a 50 ohm system, 3 dB needs two shunt resistors of 292.4 ohms and a series resistor of 17.61 ohms. For 6 dB the values are 150.5 and 37.35 ohms, for 10 dB they are 96.25 and 71.15 ohms, and for 20 dB they are 61.11 and 247.5 ohms. In a 75 ohm system, 20 dB needs 91.67 ohms and 371.3 ohms. These come from the formulas above, and the page does not list resistor tables. The higher the attenuation, the smaller the shunt resistors and the larger the series one.

How the match works

The article explains that a pad is designed for a particular source and load impedance, and that a symmetric pad is one for which both are equal. The impedance that you see looking into the input is the source impedance, when the output is terminated by the load, and the other way around.[1] This is why attenuators can be put in a line without causing reflections. A passive resistive pad cannot match two different impedances without some minimum loss, so for unequal impedances a different design, with a minimum loss, is needed. This calculator is for the equal-impedance case.

Choosing resistors

Use precision resistors, with a tolerance of 1 percent or better, and choose the nearest standard values. The match gets worse as the values drift, so check the result for the values that you actually use. At a high level of power, check that each resistor can take its share of the heat. The first shunt resistor takes most of the power in a pad with a large attenuation, so it needs the highest rating. At radio frequencies, keep the leads short, and use surface-mount or special resistors, because stray inductance and capacitance spoil the response.

Pi pad or T pad

The page also covers the T pad, which uses two series resistors and one shunt resistor, and the formulas for converting one into the other.[1] Both give the same attenuation and match the same impedances. The pi pad is often chosen when you want shunt resistors at the ends, as in a stepped attenuator built from switches. The choice may depend on which standard values are closest, or on the parts that you have.

Where pads are used

A pad lowers the level of a signal that is too strong for a receiver, an analyzer or an amplifier input. It also isolates two stages, because the pad absorbs reflections, and it can improve the match of a device whose impedance is not well controlled. Fixed pads are often built into small boxes with connectors, and the calculator gives the values for a pad that you build yourself.

Common mistakes

  • Mixing up the two kinds of resistor. The two equal ones go to ground, and the third is in the signal path.
  • Using decibels of power as voltage. The formulas use 20 log for the voltage ratio.
  • Using the wrong impedance. Use the impedance of the system, such as 50 or 75 ohms.
  • Ignoring the power rating. The resistors turn the lost power into heat.

What next

Use this often? Add Pi Attenuato to your Home screen.

Frequently asked questions

What is a pi attenuator calculator?

A tool that finds the resistor values of a symmetric pi pad for a wanted attenuation in decibels and a system impedance.

What are the resistor values for a 10 dB pi pad at 50 ohms?

Two shunt resistors of 96.25 ohms and a series resistor of 71.15 ohms.

How do I convert dB to a voltage ratio?

K = 10^(dB ÷ 20). 20 dB is a voltage ratio of 10 to 1 and a power ratio of 100 to 1.

Why does the pad keep the match?

Looking into a symmetric pad that is terminated by the load impedance, you see the same impedance, so there are no reflections.

What is the difference between a pi pad and a T pad?

A pi pad has two shunt resistors and one series resistor. A T pad has two series resistors and one shunt resistor.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools