A Reynolds number calculator finds the ratio of inertial to viscous forces in a flowing fluid and tells you whether the flow is laminar, transitional or turbulent. Enter the density, speed, a characteristic length and the viscosity of the fluid, and read the Reynolds number and the regime for a pipe.
How to use the reynolds number calculator
- Choose dynamic or kinematic viscosity, and US or metric units.
- Enter the density (dynamic case), the speed and the length.
- Enter the viscosity.
- Press Calculate.
What the number means
The Reynolds number compares inertial forces with viscous forces in a fluid [1]. At a low value the viscosity wins and the layers of fluid slide smoothly past each other; at a high value inertia wins and the flow becomes irregular and mixed. It has no unit, so it is the same in any consistent system of units. That makes it a standard number for comparing flows of very different sizes.
The formulas
The formula is Re = ρ u L ÷ μ, with the density ρ, the flow speed u, the characteristic length L and the dynamic viscosity μ. With the kinematic viscosity ν = μ ÷ ρ, it becomes Re = u L ÷ ν. The Wikipedia article writes the same pair of formulas [1]. The calculator uses the first when you give the dynamic viscosity and the second when you give the kinematic one.
Choosing the length
The characteristic length depends on the problem. For flow in a pipe, it is the inside diameter [1]. Using the radius instead would halve the number, so state what you used when you quote a result. For a non-circular duct, an equivalent diameter is used, which this calculator does not work out for you.
Flow regimes in a pipe
The Wikipedia article says that, for fully developed flow in a pipe, laminar flow occurs below 2,300 and turbulent flow above 2,900, with intermittent flow between [1]. The values are not sharp limits. The calculator uses 2,300 and 2,900 and says so with each result. The boundary is approximate.
A worked example
Take water at 10 °C, with a density of 999.7 kg/m³ and a dynamic viscosity of 0.001308 Pa·s, flowing at 1 m/s in a pipe with a diameter of 0.25 m. Then Re = 999.7 × 1 × 0.25 ÷ 0.001308 = 191,074, far above 2,900, so the flow is turbulent. The density and viscosity are values for water at 10 °C that we use for this example; look up the values for your own fluid.
Kinematic viscosity
If you know the kinematic viscosity, you do not need the density. For the water above, ν = 0.001308 ÷ 999.7 = 1.3084 × 10⁻⁶ m²/s, and Re = 1 × 0.25 ÷ 1.3084 × 10⁻⁶ gives the same 191,074. The calculator shows ν when you give μ, so you can see the link. Kinematic viscosity has units of area per time, such as m²/s or ft²/s.
US and metric units
The metric boxes take kg/m³, m/s, metres and Pa·s. The US boxes take lb/ft³, ft/s, feet and lb/(ft·s). Because Re has no unit, the calculator does not convert anything: it works directly in the units that you pick, as long as the four values use the same system. Do not give the length in inches with a speed in feet per second, as the number would be wrong.
Where it is used
Engineers use the Reynolds number to design pipes and pumps, to predict drag on a ball or a wing, and to scale a model so that it behaves like the full-size object. Turbulent flow mixes better and loses more energy to friction, while laminar flow is smooth and predictable. Other quantities, such as the friction factor, are found from Re.
Limits
The regime labels are for fully developed pipe flow, and the range between 2,300 and 2,900 is intermittent [1]. For flow past a sphere or over a plate, the critical Reynolds numbers are different. The tool gives the number correctly, but the words laminar and turbulent should be read as a rough guide only.
Common fluids
You need the density and viscosity of the fluid at its working temperature, since both change with temperature. Our example uses water at 10 °C with the density 999.7 kg/m³ and the viscosity 0.001308 Pa·s. Look up the values for your fluid and temperature from a reliable table, and keep the same system of units for all of them. Warmer water is less viscous, so the same pipe and speed give a larger Reynolds number.
Why the number matters
At a low Reynolds number the flow is smooth and predictable, and the pressure drop in a pipe grows in proportion to the speed. At a high number the flow is turbulent and mixes strongly, so the losses rise faster than the speed. Knowing the regime tells you which friction formula to choose for a design, and whether a dye injected in the pipe would stay as a thread or spread through the fluid.
Scaling a model
Wikipedia says that for two flows to be similar they must have the same geometry and equal Reynolds and Euler numbers [1]. A small model in water can therefore stand in for a large object in air, if you adjust the speed so that Re matches. The calculator lets you try the speed that gives the same number in the model and in the real case, by comparing the two results.
Common mistakes
- Using the radius instead of the diameter. That halves Re.
- Mixing viscosity types. Dynamic needs the density; kinematic does not.
- Mixing unit systems. Keep all four values in one system.
- Reading the limit as exact. The change is gradual.
What next
Use this often? Add Reynolds Num to your Home screen.
Frequently asked questions
What is a reynolds number calculator?
A tool that finds the dimensionless ratio of inertial to viscous forces in a flow and the flow regime.
What is the formula for the Reynolds number?
Re = ρ u L ÷ μ, or u L ÷ ν with the kinematic viscosity ν.
What Reynolds number is laminar flow?
In a pipe, below about 2,300; turbulent flow is above about 2,900, with intermittent flow between.
What length do I use for a pipe?
The inside diameter is the usual choice; say so when you quote the number.
Does Re have a unit?
No, it is dimensionless, so it is the same in any consistent unit system.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.