Saved

Press the star next to a tool's name to save it.

All my tools

Resistor Noise Calculator

Use this resistor noise calculator to find the thermal noise voltage √(4kTRΔf) of a resistor from its resistance, temperature and bandwidth, with the level in dBV and dBu.

Restored your last values ·

Ω
Hz

Enter the resistance in ohms, the temperature and the measurement bandwidth in hertz. You get the rms thermal noise voltage, the noise density and the noise level in dBV and dBu.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the resistance, the temperature and the bandwidth, then press Calculate.

See full result

A resistor noise calculator finds the thermal noise voltage that a resistor produces on its own, from its resistance, its temperature and the bandwidth over which you measure. Enter the three values and the page gives the rms voltage, the noise density in nanovolts per root hertz, and the level in dBV and dBu.

How to use the resistor noise calculator

  1. Choose US (°F) or metric (°C) for the temperature.
  2. Enter the resistance in ohms.
  3. Enter the temperature and the bandwidth in hertz.
  4. Press Calculate.

What thermal noise is

Every resistor above absolute zero produces a small random voltage, because its charge carriers move with thermal energy. It is called Johnson–Nyquist noise, or thermal noise [1]. It sets a floor for the smallest signal that an amplifier can pick up from a source of that resistance, which is why it matters at the input of sensitive circuits.

The formula

The rms noise voltage is E = √(4 k T R Δf), where k is the Boltzmann constant, T is the absolute temperature in kelvin, R is the resistance in ohms and Δf is the bandwidth in hertz. The Wikipedia article writes the same mean-square form, with the constant k = 1.380649 × 10⁻²³ joules per kelvin [1]. The calculator uses exactly that constant, and it changes °F or °C into kelvin before it finds the root.

A worked example

Take a 20 kilohm resistor at 20 °C, which is 293.15 K, over a bandwidth of 1 kHz. The product 4 k T R Δf is 3.2380 × 10⁻¹³, and its square root is 5.6903 × 10⁻⁷ volts, or 569.03 nanovolts. As a check, Wikipedia's figure of about 13 nV/√Hz for 10 kΩ [1] scales by √2 for 20 kΩ to about 18 nV/√Hz, in line with this result. In US units the same case is 68 °F, and the calculator gives the same answer.

Noise density

Dividing the voltage by the square root of the bandwidth gives the noise density, in nanovolts per root hertz. For the example it is 17.994 nV/√Hz. The density does not depend on the bandwidth, so it is the handy number to compare resistors. The Wikipedia article says that a 10 kilohm resistor has about 13 nV/√Hz at room temperature [1], and the calculator gives 12.72 nV/√Hz for 10 kilohms at 293.15 K, close to that figure.

The noise level in dBV and dBu

The voltage can be given as a level, Lu = 20 log₁₀(E ÷ V₀), with V₀ = 1 volt for dBV and V₀ = 0.77459667 volts for dBu, the voltage that dissipates 1 milliwatt in 600 ohms [2]. For the example, E is −124.90 dBV and −122.68 dBu. The negative sign means the noise is far below the reference. Audio engineers often quote noise in dBu, while dBV is common for measurements that use 1 volt as the reference.

What changes the result

The noise grows with the square root of the resistance, the temperature and the bandwidth. Four times the resistance, or four times the bandwidth, doubles the voltage. Raising the temperature from 20 °C to 100 °C raises the noise by about 13%, because the absolute temperature goes from 293.15 K to 373.15 K. Cooling a resistor therefore lowers its noise.

What the formula leaves out

The formula covers thermal noise only. Real resistors can also show other noise, such as current noise, that depends on the type of resistor and on the current through it; this note is our own and is not part of the formula. The result is therefore the lowest noise you can expect from the stated resistance; a real part may be noisier, especially with a current flowing through it.

Choosing the bandwidth

The bandwidth is the range of frequencies that the measuring system passes, in hertz. For an audio measurement it may be 20 kHz; for a narrow filter it may be a few hertz. The Wikipedia article gives the example that about 3 kilohms gives almost one microvolt of rms noise over 20 kHz [1], and the calculator gives 0.9856 µV for 3 kilohms at 293.15 K over 20 kHz, which agrees.

Using the result

Compare the noise voltage with the smallest signal that you need to detect. If the signal is not much larger than the noise, use a lower resistance, a narrower bandwidth, or a cooler part. Add the noise of several resistors in a root-sum-square way only if they are independent; this tool does not cover that, so treat this tool as a calculation for a single resistance.

Comparing resistors

Because the voltage grows with the square root of the resistance, a 1 megohm resistor is only about 10 times noisier than a 10 kilohm one, not 100 times, at the same temperature and bandwidth. Use the noise density to compare parts without choosing a bandwidth. For a 1 kilohm resistor at 20 °C the density is about 4.0 nV/√Hz, and for 100 kilohms it is about 40 nV/√Hz. These values come from the formula.

Noise in an amplifier input

The noise of the source resistance is amplified together with the signal, so it matters most at the first stage. A designer compares the thermal noise of the source with the noise of the amplifier itself. When the resistor noise dominates, a better amplifier does not help, and the only remedies are a lower resistance, a narrower bandwidth or a lower temperature.

Common mistakes

  • Entering the temperature in the wrong scale. Check the US or metric choice.
  • Using a bandwidth in kilohertz. Enter hertz.
  • Taking the result as the noise of the whole circuit. It covers one resistor.
  • Ignoring excess noise. Real resistors add to it.

What next

Use this often? Add Resistor Noi to your Home screen.

Frequently asked questions

What is a resistor noise calculator?

A tool that finds the thermal noise voltage of a resistor from its resistance, temperature and bandwidth.

What is the formula for resistor noise?

E = √(4 k T R Δf), with k the Boltzmann constant, T in kelvin, R in ohms and Δf in hertz.

Does the noise depend on current?

Thermal noise does not; current noise is a separate effect that this calculator does not include.

Why does a larger resistance make more noise?

The noise voltage grows with the square root of the resistance.

What does dBu mean here?

A level relative to 0.77459667 volts; dBV is relative to 1 volt.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools