This dBm to watts converter changes a power level in decibel-milliwatts into watts, milliwatts or microwatts, and converts watts back to dBm. Enter a value, choose the direction and the result shows the same power in dBm, dBW, watts, milliwatts and microwatts, using the standard logarithmic formula.
What is dBm?
The dBm is a power level on a logarithmic decibel scale, referenced to one milliwatt (1 mW). According to Wikipedia, a similar unit, dBW, is referenced to one watt (1,000 mW) instead. Because dBm is tied to a fixed reference it is an absolute quantity, even though it is written like a ratio. It is not an SI unit. Radio engineers use dBm for transmit power, receiver sensitivity and signal strength, while audio and telephony work often uses a 600-ohm reference and radio frequency work a 50-ohm one.
The dBm to watts formula
dBm = 10 × log10(P ÷ 1 mW)
P (mW) = 1 mW × 10^(dBm ÷ 10)
P (W) = 10^((dBm − 30) ÷ 10)
The first two formulas come from Wikipedia. The third follows by dividing milliwatts by 1,000: since 1 W is 30 dBm, subtracting 30 from the dBm figure gives dBW, and the power in watts is ten to the power of dBW divided by ten.
How to use the dBm to watts converter
- Pick the direction. Choose dBm to watts, or watts to dBm.
- Enter your number. Negative dBm values are fine. Watts must be greater than zero.
- Press Calculate. The answer appears in the most readable unit, with the full set of units in the table below it.
Worked examples
- 0 dBm is 1 mW, the reference level.
- 20 dBm is 100 mW, a typical level for 2.4 GHz Wi-Fi and a Bluetooth Class 1 radio.
- 30 dBm is 1 W, about the power of a GSM mobile phone transmission.
- 40 dBm is 10 W.
- −30 dBm is 1 µW, and −10 dBm is 100 µW.
- 3 dBm is about 2 mW, because every +3 dB roughly doubles the power. The exact figure is 1.9953 mW.
- 0.5 W is 500 mW, which is 26.99 dBm.
Rules of thumb for decibels
Every 10 dB is a tenfold change in power, and every 20 dB is a hundredfold change. A change of 3 dB is roughly a doubling or halving. These shortcuts let you estimate in your head: if a transmitter is at 17 dBm, that is 20 dBm minus 3 dB, so about half of 100 mW, or 50 mW. Adding decibels is the same as multiplying power, which is why link budgets that add gains and subtract losses are done in dB.
dBm and dBW
The two units differ by exactly 30 dB. A power of 0 dBW is 1 W, which is 30 dBm. To convert a dBW value to dBm, add 30, and to convert dBm to dBW, subtract 30. The table in the results shows both so that you can match whichever unit a datasheet uses.
Where dBm is used
Wi-Fi access points, Bluetooth radios, cellular phones, antennas and amplifiers all list power in dBm. A received signal is usually a negative number, because it is far below one milliwatt: Wikipedia lists −100 dBm as 0.1 pW. A very small figure means a very weak signal, so −60 dBm is much stronger than −90 dBm even though both are small negative numbers.
Quick reference table
| dBm | Power |
|---|---|
| −30 | 1 µW |
| −10 | 100 µW |
| 0 | 1 mW |
| 10 | 10 mW |
| 17 | 50.12 mW |
| 20 | 100 mW |
| 23 | 199.5 mW |
| 27 | 501.2 mW |
| 30 | 1 W |
| 33 | 1.995 W |
| 40 | 10 W |
Adding powers in dB
Two signals of 20 dBm each do not make 40 dBm. Each is 100 mW, so together they carry 200 mW, which is 23.01 dBm. To combine levels, convert each to milliwatts or watts, add the powers, and convert the total back with the formula. Gains and losses, on the other hand, can be added directly in dB: a transmitter at 20 dBm feeding a cable with 3 dB of loss and an antenna with 5 dB of gain gives 22 dBm, which is about 158.5 mW.
Reading a datasheet
Radio datasheets often give transmit power in dBm and receiver sensitivity as a negative dBm. When you compare two products, convert both to watts to see the real size of the difference. A 23 dBm radio does not transmit 15 percent more than a 20 dBm one: it transmits about twice as much, because 3 dB is a doubling.
Why the scale is logarithmic
Human senses and radio signals both cover enormous ranges. A transmitter might send out a watt while a receiver on the other side of a room picks up a few billionths of a watt. Writing both in watts gives numbers with many zeros, while the dBm scale gives figures such as 30 and −60 that are easy to compare. Because adding decibels multiplies powers, engineers can add the gains of amplifiers and subtract the losses of cables and walls in one simple sum, then convert the final figure to watts only when they need the real power.
Common mistakes
- Treating dBm as a ratio. It is an absolute level against 1 mW, so you cannot add two dBm values to get their combined power. Convert to watts, add, then convert back.
- Mixing up dBm and dBW. They differ by 30.
- Using 10 instead of 20 for voltage. This tool deals with power only, where the factor is 10.
What next
Use this often? Add dBm to Watts to your Home screen.
Frequently asked questions
How does a dBm to watts converter work?
Use P in watts = 10 raised to (dBm − 30) ÷ 10. For example, 30 dBm is 10^0 = 1 W and 20 dBm is 10^−1 = 0.1 W.
How many watts is 0 dBm?
0 dBm is 1 milliwatt, which is 0.001 watts. It is the reference level for the dBm scale.
What is the difference between dBm and dBW?
dBm is referenced to 1 milliwatt and dBW to 1 watt. A power of 0 dBW is 1 W, which equals 30 dBm.
How do you convert watts to dBm?
Use dBm = 10 × log10(power in watts × 1,000). For example, 0.5 W is 500 mW, and 10 × log10(500) is about 26.99 dBm.
Why is dBm used instead of watts?
Radio signals span a huge range of power, from watts at a transmitter to picowatts at a receiver. A logarithmic scale keeps the numbers small and turns gains and losses into simple addition.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.