A residence time calculator gives the average time a fluid stays in a tank, reactor, pond or lake. Enter the volume and the flow rate for the residence time, or the time and one of the others for the missing quantity. For a reactor you can also add a rate constant to see how much reacts.
How to use the residence time calculator
- Choose the time unit and what you want to find.
- Enter the volume, the flow rate or the residence time.
- Optionally add a rate constant for a stirred-tank reaction.
- Press Calculate.
The basic formula
For a steady, conservative flow, the turnover time equals the amount of fluid in the control volume divided by the flow rate, τ = m / f [1]. For an ideal reactor, the theoretical residence time is always the reactor volume divided by the volumetric flow rate, τ = V / Q [2]. The calculator uses V ÷ Q, with any volume unit as long as the flow uses the same one.
Names for the same ratio
The page says that for liquids the ratio is also called the hydraulic retention time, or hydraulic residence time or detention time [1]. In chemical engineering it is known as the space time [1], and the stirred-tank page calls τ the space time of the reactor [2]. It is also called turnover or flushing time. Its inverse, the number of times the volume is replaced per unit of time, is the turnover rate, and the calculator shows it, as our own working.
Worked examples
A tank of 1,000 litres that receives 500 litres per hour has a residence time of 2 hours, which is 120 minutes or 7,200 seconds, and it turns over 0.5 times per hour. A reactor of 100 cubic metres fed with 10 cubic metres per minute holds the fluid for 10 minutes. The second mode gives the volume needed for a target time, and the third gives the flow needed to reach a target time in a given volume. These figures are our own arithmetic.
Reaction in a stirred tank
For an ideal stirred tank, the page gives the outlet concentration of a first-order reaction as C = C₀ ÷ (1 + kτ) [2]. With k = 0.5 per hour and τ = 2 hours, the outlet is half the inlet, so half is converted. Enter the rate constant per the same time unit as the residence time. The page also notes that an ideal reactor is perfectly mixed when the residence time is 5 to 10 times the mixing time [2].
Mean, not exact
The residence time distribution of an ideal stirred tank is an exponential with a mean of τ, and that of an ideal plug-flow reactor is a spike at τ [1]. Real vessels lie between the two. The page also warns that a compound's residence time equals the turnover time only if it does not react and its concentration is uniform [1]. So V ÷ Q is the mean for the fluid, not for every particle.
Typical uses
Engineers use residence time to size reactors, settling basins and storage tanks. The page notes that the hydraulic retention time of a sedimentation basin is about two hours [1]. Environmental scientists use the same ratio for lakes and for pollutants in a reservoir. A longer residence time gives more time for a reaction or for settling, but needs a larger volume.
Checking units
The flow rate and the volume must use the same volume unit, for example litres and litres per hour. The time unit you choose applies to the flow rate, the residence time and the rate constant. If you have a flow in cubic metres per day and a volume in litres, convert one of them first.
Sizing a vessel
If you need the fluid to stay for a set time, choose the volume mode. A settling tank that must hold water for two hours at 500 cubic metres per hour needs 1,000 cubic metres. In a chemical reactor the residence time is set by the reaction rate, and the volume follows from the flow you want to process. The same calculation sizes holding tanks, contact chambers for disinfection and ponds.
Lakes and reservoirs
For a lake, the volume divided by the outflow gives the flushing time. A lake with a volume of 50 million cubic metres and an outflow of 100,000 cubic metres per day has a residence time of 500 days, so a pollutant that enters it will take a long time to leave. Use days as the time unit and the same volume unit in both boxes.
Going further
For a reaction that is not first order, or for vessels that are not well mixed, the simple conversion in the calculator does not apply. Use the residence time as a starting point, and consult a reactor design text for the right model.
Common mistakes
- Mixing volume units. Use the same volume unit for V and Q.
- Mixing time units. The flow, the time and the rate constant use the chosen unit.
- Assuming every particle stays τ. τ is a mean value.
- Using it with changing volume. V ÷ Q assumes a steady flow at constant volume.
What next
Use this often? Add Residence Ti to your Home screen.
Frequently asked questions
What is a residence time calculator?
A tool that gives the average time a fluid stays in a vessel, from the volume and the flow rate.
What is the formula for residence time?
τ = V ÷ Q, the volume divided by the volumetric flow rate.
Is residence time the same as retention time?
For liquids, yes: it is also called hydraulic retention time, space time or turnover time.
How much reacts in a stirred tank?
For a first-order reaction in an ideal stirred tank, the outlet is C₀ ÷ (1 + kτ).
Is every particle in the tank for exactly τ?
No. τ is the mean. Real tanks have a spread of residence times.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.