A RAID calculator shows how much usable space you get from a set of drives at each RAID level, how much goes to redundancy, and how many drive failures the array can survive. Choose RAID 0, 1, 5, 6 or 10, enter the number of drives and their size, and you get the answer in gigabytes or terabytes, together with the minimum number of drives for the level. It runs in your browser.
How to use the RAID calculator
- Choose the RAID level.
- Enter the number of drives and the size of each drive.
- Press Calculate.
The levels
The Wikipedia article on the standard RAID levels describes RAID 0 as striping across two or more disks with no parity, redundancy or fault tolerance. RAID 1 keeps an exact copy, a mirror, of the data on two or more disks. RAID 5 uses block-level striping with distributed parity, so that no data is lost after the failure of a single drive, and RAID 6 adds a second parity block.[1] The article on nested levels describes RAID 10 as a RAID 0 array of mirrors, which needs at least four drives.[2] The calculator gives usable capacity for each of these.
The capacity formulas
The pages give the space efficiency of each level as a fraction of the raw capacity, and we turn the fractions into the formulas that the calculator uses. RAID 0 has an efficiency of 1, so the usable space is the number of drives times their size. RAID 1 has an efficiency of 1 ÷ n, and the usable space is one drive's worth. RAID 5 has 1 − 1 ÷ n, which is (n − 1) drives' worth, and RAID 6 has 1 − 2 ÷ n, or (n − 2). RAID 10 with two-way mirrors has an efficiency of 1 ÷ 2, so it gives n ÷ 2 drives' worth.[1][2] The page's example is three drives of 250 gigabytes in RAID 5, which have a total capacity of 750 gigabytes, but only 500 gigabytes is usable for data.[1]
Minimum drives and fault tolerance
The table of the standard levels gives the minimum number of drives as two for RAID 0 and 1, three for RAID 5 and four for RAID 6. It says that RAID 0 has no fault tolerance, that RAID 1 survives the loss of all drives but one, that RAID 5 survives one failed drive and RAID 6 survives two.[1] For RAID 10, the nested page says that it survives at least one failure, and up to one in each mirrored pair, as long as both drives of a pair do not fail.[2] The calculator shows these for the number of drives that you enter.
Mixed drive sizes
The article says that a RAID 1 array can only be as big as its smallest member, and that RAID 0 is limited to the size of the smallest disk, although some implementations can use the rest.[1][2] Its example for RAID 0 is a 120 gigabyte disk striped with a 320 gigabyte disk, which gives 120 × 2 = 240 gigabytes.[2] For the other levels the pages do not say, but the usual rule is the same, so the calculator assumes equal drives. If yours differ, enter the size of the smallest one.
Choosing a level
RAID 0 gives the most space and speed, but one failure loses everything. RAID 1 is simple and safe but costs half of the space with two drives. RAID 5 is a good balance for three or more drives, since it loses only one drive's worth of space, but a failure puts the array at risk until it is rebuilt. RAID 6 survives two failures, which matters with large drives. RAID 10 gives speed and safety at the cost of half of the space. The calculator shows these trade-offs for your drives.
Rebuild times and backups
The pages note that larger arrays of larger drives increase the time that it takes to recover from a fault, and that the failure-rate figures assume that no drives are rebuilt. They also say that RAID cannot replace a backup plan, because it does not protect against user error, software faults or malware.[1][2] Keep a separate copy of important data, on another device or in another place.
An example
With six drives of 8 terabytes, RAID 5 gives 40 terabytes of usable space, RAID 6 gives 32, and RAID 10 gives 24, while RAID 0 would give 48. The calculator also shows how much of the 48 terabytes of raw space goes to redundancy in each case, which is 8, 16 and 24 terabytes for the three safe levels.
Capacity and performance
The calculator reports capacity, but the levels also differ in speed. Striping spreads reads and writes over several drives, which raises throughput, while mirroring can serve reads from either copy. Parity levels pay a cost for each write, because the parity has to be updated. If your workload writes a lot of small blocks, that cost may matter more than the space, and RAID 10 is often chosen for that reason. The pages describe these methods in general terms, and they give no speed figures.
Common mistakes
- Counting a RAID as a backup. It only survives drive failures.
- Forgetting the file system. Usable space is slightly less after formatting.
- Mixing drive sizes. The smallest drive sets the size of each member.
- Using RAID 5 with very large drives. Long rebuilds raise the risk, so consider RAID 6.
What next
Use this often? Add RAID to your Home screen.
Frequently asked questions
What is a RAID calculator?
A tool that finds the usable capacity and fault tolerance of a RAID array from the level, the number of drives and their size.
How much usable space does RAID 5 give?
(n − 1) drives' worth. Three 250 GB drives give 500 GB of the 750 GB total.
How much usable space does RAID 6 give?
(n − 2) drives' worth, and it survives two failed drives.
How many drives does RAID 10 need?
At least four, in mirrored pairs. The usable space is half of the total.
Is RAID a backup?
No. It protects against drive failure, not against deletion, malware or software faults.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.