Saved

Press the star next to a tool's name to save it.

All my tools

Psig to Psia Converter

Use this psig to psia converter to add or subtract atmospheric pressure, with kPa and bar shown too. It uses 14.6959 psi unless you enter your own.

Restored your last values ·

psi

Leave atmospheric pressure blank to use standard sea-level pressure, 14.6959 psi. Enter your own figure for a high-altitude site or a given day.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter a value and press Calculate.

See full result

A psig to psia converter turns a gauge pressure reading into absolute pressure, or back again. Enter the pressure, choose the direction and the calculator adds or subtracts atmospheric pressure for you. It uses standard sea-level pressure unless you enter your own figure, and it also shows the answer in kilopascals and bar.

What psig and psia mean

Both units measure pressure in pounds of force per square inch. The difference is the zero point. Psig means pounds per square inch gauge: it is measured against the air around you, so a tire gauge that reads 0 in open air shows 0 psig. Psia means pounds per square inch absolute: it is measured against a perfect vacuum, so the air around you already counts as about 14.7 psia. Wikipedia describes psia as used to make clear that a pressure is relative to a vacuum rather than to ambient pressure, and psig as relative to atmospheric pressure.

The psig to psia formula

Absolute pressure (psia) = gauge pressure (psig) + atmospheric pressure
Gauge pressure (psig) = absolute pressure (psia) − atmospheric pressure

At sea level the standard atmosphere is 101,325 pascals, which is about 14.6959 psi. Most everyday work rounds this to 14.7 psi. The calculator keeps the full 14.6959 figure by default, so its answers differ slightly from a hand calculation that rounds to 14.7.

How to use the psig to psia converter

  1. Choose the direction. Pick psig to psia if you have a gauge reading, or psia to psig if you have an absolute figure.
  2. Enter the pressure. Negative gauge readings are fine, because a gauge can read below atmospheric pressure when it measures a partial vacuum.
  3. Add atmospheric pressure if you know it. Leave the box empty for standard sea-level pressure.
  4. Press Calculate. The result shows both pressures, the atmospheric pressure used and the absolute pressure in kPa and bar.

Worked example

Wikipedia gives an example of 65 psig at sea level. Adding atmospheric pressure of 14.7 psi gives 79.7 psia. Enter 65 with an atmospheric pressure of 14.7 to see exactly that result. In the other direction, 79.7 psia minus 14.7 psi gives 65 psig. With the default 14.6959 psi the same 65 psig comes out as 79.6959 psia.

A vacuum example: a gauge that reads −5 psig at sea level is measuring an absolute pressure of 9.6959 psia, which is less than the surrounding air. The lowest gauge reading possible at sea level is about −14.7 psig, which is a perfect vacuum at 0 psia.

Why atmospheric pressure matters

Atmospheric pressure is typically about 100 kPa at sea level but changes with altitude and with the weather. Because a gauge reads relative to the air around it, the same absolute pressure gives a different gauge reading at different heights. Wikipedia notes, for example, that a car driving up a mountain shows a higher gauge tire pressure because the pressure outside falls. If you work at a high site, look up the local atmospheric pressure and enter it in the optional box.

Converting to other units

One psi is approximately 6,894.757 pascals, or about 6.895 kilopascals, and about 0.06895 bar. The converter uses these factors for the kPa and bar figures. For a wider range of units such as atmospheres, torr and inches of water, use the pressure converter.

When to use gauge and when to use absolute pressure

Gauge pressure is what most pressure gauges, tire gauges and compressor dials show, so it is the natural unit for inflating, testing and operating equipment. Absolute pressure is needed where the amount of gas matters, as in the ideal gas law, in compressor and vacuum calculations, and in any formula that assumes zero means no pressure at all. A common source of error is putting a gauge figure into one of those formulas without first adding atmospheric pressure.

Absolute pressure in gas calculations

Gas laws such as the ideal gas law relate the pressure, volume, amount and temperature of a gas, and they work only with absolute pressure and absolute temperature. If a tank gauge reads 100 psig at sea level, the gas inside is at 114.6959 psia, so it is compressed to about 7.8 times atmospheric pressure, not 6.8 times. Using the gauge figure directly would give an answer that is wrong by about 13 percent. Converting to psia first removes that error.

Quick reference

Gauge (psig)Absolute (psia)Absolute (kPa)
014.6959101.325
1024.6959170.27
3044.6959308.17
6579.6959549.5
100114.6959790.8

Checking a reading against your own gauge

If you have a gauge and a source with a known absolute pressure, you can use this converter as a check. An unloaded gauge open to the air should read 0 psig. If it does not, the gauge is out of adjustment, and any figure you convert from it will be off by the same amount. Many gauges are labelled psi without a suffix, and most of the time that means psig, but a sensor marked psia reads absolute pressure and will show about 14.7 in open air at sea level.

Common mistakes

  • Forgetting to convert before using a gas law. Gas-law formulas need absolute pressure.
  • Using 14.7 as if it never changes. It is a sea-level standard, not a constant for every place.
  • Mixing units. Add atmospheric pressure in the same unit as the reading, which here is psi.
  • Ignoring the suffix. A figure written as psi with no letter is often gauge pressure, but check the source.

What next

Use this often? Add Psig to Psia to your Home screen.

Frequently asked questions

How do you use a psig to psia converter?

Add atmospheric pressure to the gauge reading. At sea level that is about 14.7 psi, so 65 psig is about 79.7 psia.

How do you convert psia to psig?

Subtract atmospheric pressure from the absolute pressure. For example, 79.7 psia minus 14.7 psi is 65 psig.

What is standard atmospheric pressure in psi?

One standard atmosphere is 101,325 pascals, which is approximately 14.6959 psi. It is often rounded to 14.7 psi.

Can psig be negative?

Yes. A negative gauge reading means the pressure is below the surrounding atmospheric pressure, as in a partial vacuum. Absolute pressure can never be negative.

Does altitude change psig?

The same absolute pressure reads differently on a gauge at different altitudes, because atmospheric pressure falls as you go up. Enter the local atmospheric pressure for an exact answer.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools