Saved

Press the star next to a tool's name to save it.

All my tools

Porosity and Permeability Calculator

Use this porosity and permeability calculator to find porosity from volumes or densities, and permeability from a Darcy flow test or the Kozeny–Carman equation, in SI and darcy.

Restored your last values ·

Choose a method. For porosity, enter either the void and total volumes or the bulk and particle densities. For permeability, enter the flow data of a Darcy test in SI units, or the porosity and grain size of a packed bed.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to work out and fill in the boxes, then press Calculate.

See full result

A porosity and permeability calculator gives the two basic properties of a porous material such as soil, sand or rock. Porosity is the share of the volume that is empty space. Permeability tells you how easily a fluid flows through it. Enter volumes, densities or the data of a flow test, and it gives the results in SI units and in darcy.

How to use the porosity and permeability calculator

  1. Choose what to work out.
  2. Enter the values for that method, using the unit shown in each label.
  3. Press Calculate.
  4. Read the result and the line that shows how it was found.

What porosity means

Wikipedia defines porosity as the fraction of void space in a material, φ = V_V ÷ V_T, where V_V is the volume of the voids and V_T the total, or bulk, volume [1]. It ranges from less than 0.005 for solid granite to more than 0.5 for peat and clay [1]. In the first mode, enter the two volumes in any unit and get the porosity as a fraction and a percentage, together with the solid share.

Porosity from density

Often you know the dry bulk density of a sample and the density of its grains. For air-filled pores, Wikipedia gives φ = 1 − ρ bulk ÷ ρ particle [1]. If the pores hold a fluid, the general form is φ = (ρ particle − ρ bulk) ÷ (ρ particle − ρ fluid) [1]. Leave the fluid box blank for air. A bulk density of 1.6 and a particle density of 2.65 give 0.396, in the range that the page gives for sandy soil [1].

Typical values

The Wikipedia page quotes sandy soil with a bulk density of 1.5 to 1.7 grams per cubic centimetre as having a porosity of about 0.36 to 0.43, and clay soil with a bulk density of 1.1 to 1.3 as 0.51 to 0.58 [1]. It gives a mean particle density of about 2.65 for silica-rich sediments and 2.70 for carbonate sediments [1]. Use them as a check on your own result.

Darcy's law and permeability

Darcy's law states that Q = k A Δp ÷ (μ L), where Q is the discharge rate, A the cross-sectional area, Δp the pressure difference, μ the dynamic viscosity and L the length of the path [3]. Rearranged for the permeability, k = Q μ L ÷ (A Δp), by our own algebra. The flow-test mode uses this with SI units: cubic metres per second, pascal seconds, metres, square metres and pascals. The result is in square metres.

Darcy units

Permeability is also given in darcy, a unit of the oil industry. One darcy is about 9.87 × 10⁻¹³ square metres [4], and the calculator uses that figure to give darcy and millidarcy beside the SI value. As an example of our own, a flow of 10⁻⁶ cubic metres per second at a viscosity of 0.001 pascal seconds through 0.5 metres, 0.01 square metres and 1,000 pascals gives 5 × 10⁻¹¹ square metres, about 50.7 darcy.

Porosity from residence time

In its Darcy mode, the calculator also gives porosity as φ = Q t ÷ (A L), using the residence time t, the time that the fluid takes to cross the sample. This is our own working from the definitions of flow and volume. It offers the result when you enter a time. With the example above and 200 seconds, the result is 0.04. This porosity counts only the connected voids that the fluid fills, so it is not the same thing as the volume ratio of the first modes.

Darcy velocity

The Darcy velocity is the flow rate per unit cross-sectional area [3]. The calculator therefore shows Q ÷ A in metres per second. It is a superficial speed, as if the fluid filled the whole cross-section, and it is lower than the real speed of the fluid in the pores. The calculator does not give the real speed.

The Kozeny–Carman equation

For a packed bed of particles, Wikipedia gives κ = Φs² ε³ dp² ÷ [150 (1 − ε)²], where ε is the porosity, dp the diameter of the equivalent sphere and Φs the sphericity, 1.0 for spheres [2]. The page quotes a porosity of about 0.37 for randomly packed spheres [2]. With 1 millimetre spheres, the calculator gives 8.5 × 10⁻¹⁰ square metres, about 862 darcy. Other texts may use a different constant; this page gives 150.

When the equations apply

Wikipedia says that the Kozeny–Carman equation is valid only for creeping flow, the slowest limit of laminar flow, up to a particle Reynolds number of about 1 [2]. The Kozeny–Carman equation is the only link between porosity and permeability that this tool offers. Wikipedia adds that clays can have a high porosity and a low permeability [1], so do not infer one from the other.

Using the calculator

Pick the method that fits your data. For a quick soil check, use the density mode. For a column test, use Darcy's law and enter SI values, converting litres, centimetres and kilopascals first. For a bed of beads or sand, use Kozeny–Carman with the grain size and the porosity. The result lines show the formula with your numbers, so you can follow the arithmetic and compare it with a handbook.

Common mistakes

  • Mixing units in Darcy's law. Use SI values for every input.
  • Confusing total and connected porosity. Only connected voids let fluid through.
  • Using Kozeny–Carman for fast flow. It holds for creeping flow only.
  • Entering a bulk density above the particle density. Porosity cannot be negative.

What next

Use this often? Add Porosity and to your Home screen.

Frequently asked questions

What is a porosity and permeability calculator?

A tool that finds the void fraction of a material and how easily a fluid flows through it.

How do you calculate porosity?

φ = void volume ÷ total volume, or φ = 1 − bulk density ÷ particle density for air-filled pores.

What is permeability?

A measure of how easily a fluid flows through a porous material, in square metres or darcy.

How many square metres is one darcy?

About 9.87 × 10⁻¹³ square metres.

Does high porosity mean high permeability?

Not always: clays have high porosity but low permeability.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools