A differential pressure calculator gives the difference between two pressures, and the pressure drop across a valve or other flow device from the flow rate, the flow factor Kv and the specific gravity of the liquid. It also works backwards to find the flow or the Kv from a measured pressure drop. Pressures are in bar and flows in cubic metres per hour.
How to use the differential pressure calculator
- Choose what to work out from the list.
- Fill in the boxes that appear: two pressures, or the flow, Kv, specific gravity and pressure drop.
- Press Calculate and read the result in bar, kPa and psi.
What differential pressure means
Differential pressure is simply the difference between two pressures in the same system, for example the pressure before and after a filter, a valve, a pump or a heat exchanger. It is written ΔP = P₁ − P₂. This is our own definition, since the sources do not spell it out as a formula. Both pressures must be gauge pressures or both absolute pressures. A growing differential across a filter, for instance, is a sign that it is clogging.
Subtracting two pressures
The first mode subtracts the downstream pressure from the upstream pressure. With 6.5 bar upstream and 5.2 bar downstream the differential pressure is 1.3 bar, which is 130 kPa or about 18.9 psi. If the downstream value is higher, the answer is negative and the calculator says so. The conversion factors, 1 bar = 100 kPa and 1 bar = 14.5038 psi, are our own working.
The flow factor Kv
For valves, the Kv is the flow factor in the metric system. The Wikipedia page gives it in cubic metres per hour, with the flow Q in cubic metres per hour, the pressure drop ΔP in bar and the relative density of water taken as 1 [1]. In the usual definition, it is the flow of water that gives a drop of 1 bar, which is our own wording. A larger Kv means a more open device: it passes more flow for the same drop.
The pressure drop formula
The calculator uses ΔP = S × (Q ÷ Kv)², with Q and Kv in cubic metres per hour and ΔP in bar. This comes from the relation Kv = Q × √(S ÷ ΔP) on the Wikipedia page for the flow coefficient [1]. Solving it for the drop and for the flow gives the other two forms, Q = √(Kv² × ΔP ÷ S) and ΔP = S × (Q ÷ Kv)², which is our own algebra. The square means that the drop is very sensitive to the flow: if the flow doubles, the drop grows four times, and the calculator reminds you of that with each result.
A worked example
Take a flow of 10 cubic metres per hour through a device with Kv = 5 and a liquid with a specific gravity of 1. Then Q ÷ Kv = 2, its square is 4 and the pressure drop is 4 bar, a result that follows directly from the formula above and is our own worked case. In the reverse direction, with 4 bar and Kv = 5, the flow is 5 × √4 = 10 cubic metres per hour. With 10 and 4, the Kv is 10 × √(1 ÷ 4) = 5.
Specific gravity
Specific gravity, or relative density, is a dimensionless ratio of the density of a substance to the density of a reference material, which for liquids is usually water [2]. Water is 1, so you can leave the box empty for water. A heavier liquid, with a value above 1, gives a larger pressure drop for the same flow, and a lighter one gives less. The sources do not list specific gravities for particular fluids, so look up the value for your liquid, as the calculator does not guess it.
Cv and Kv
In the United States, the flow coefficient is often given as Cv, which uses gallons per minute and psi instead of cubic metres per hour and bar. The conversion given on the Wikipedia page is Cv = 1.156 × Kv [1]. When you work out a Kv, the calculator also shows the matching Cv, so you can compare a metric data sheet with a US one.
Units and the definition of Kv
Wikipedia defines Kv as the water flow in cubic metres per hour at a pressure drop of 1 kgf/cm² across a fully open valve, and uses bar for the drop in its formula [1]. One kgf/cm² is a little under 1 bar, a small difference that this tool ignores, and that is our own note. To stay consistent, this tool uses cubic metres per hour for flow and Kv and bar for pressure throughout. If your data sheet gives a Kv in other units, convert it before you enter it. Only the ratio Q ÷ Kv enters the formula, so any pair of flow units that match each other gives the same ratio.
Limits of the formula
The formulas apply to liquids in turbulent flow through a valve or device that has a known Kv. They do not apply to gases, which are compressible, nor to liquids that flash into vapour or cavitate, and this limit is our own caveat. They also do not give the loss in a long pipe, an orifice plate or a bend. For those, use a pipe-flow method. The page we read gives no such formulas, so we have not added any.
Practical uses
Differential pressure tells you if a filter needs changing, if a pump is making the pressure that you expect, and how much a control valve is throttling the flow. Measure both pressures at the same time and in the same units, enter them in the first mode, and compare the answer to the limit of the maker. Use the valve modes to check that a valve is large enough for a required flow.
Common mistakes
- Mixing gauge and absolute pressures. Use two readings of the same kind.
- Entering a Kv in the wrong units. The tool expects cubic metres per hour.
- Forgetting the specific gravity. A heavy liquid needs a value above 1.
- Using the Kv formulas for gas. They are for liquids only.
What next
Use this often? Add Differential to your Home screen.
Frequently asked questions
What is a differential pressure calculator?
A tool that finds the difference between two pressures, and the pressure drop, flow or Kv of a valve or flow device.
How do I calculate differential pressure?
Subtract the downstream pressure from the upstream pressure, ΔP = P₁ − P₂, using the same units and the same kind of pressure for both.
What is the formula for the pressure drop of a valve?
ΔP = S × (Q ÷ Kv)², with Q and Kv in cubic metres per hour, ΔP in bar and S the specific gravity, where water is 1.
How do I convert Kv to Cv?
Multiply the Kv by 1.156 to get the Cv, which uses US gallons per minute and psi.
Does the formula work for gases?
No. It is for liquids in turbulent flow, not for gases or for liquids that flash or cavitate.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.