A pressure calculator works out how strongly a force pushes on a surface. The same push feels very different depending on the area that it's spread over, which is why a sharp knife cuts well and snowshoes stop you from sinking. Enter the force and the area, and this pressure calculator gives you the result, along with the same value in other common units. You can also rearrange the problem to find the force or the area if you already know the pressure. Choose US units for pounds-force and square inches, or Metric for newtons and square meters.
How to use the pressure calculator
- Choose what to find: pressure, force or area.
- Choose US or Metric units.
- Enter the two values that you know.
- Press Calculate.
- Read the answer and the conversions shown below it.
What is pressure?
Pressure is the force applied perpendicular to the surface of an object per unit area over which that force is distributed. It's a scalar quantity, so it has a size but no direction of its own. The SI unit is the pascal, which is one newton per square meter. In the imperial and US customary systems, the traditional unit is the pound-force per square inch, or psi.
The pressure formula
The relationship is simple: pressure equals force divided by area, or P = F / A. Here, P is the pressure, F is the magnitude of the force acting at right angles to the surface, and A is the area of contact. The same equation can be rearranged to find either of the other two values.
| To find | Formula | US units | Metric units |
|---|---|---|---|
| Pressure | P = F ÷ A | psi | Pa |
| Force | F = P × A | lbf | N |
| Area | A = F ÷ P | in² | m² |
Worked examples
Suppose that a 200 lbf load rests on a plate with an area of 4 square inches. The pressure is 200 ÷ 4 = 50 psi, which is about 344.7 kPa. Now try it in metric units. A force of 500 N acting on 0.25 square meters gives 500 ÷ 0.25 = 2,000 Pa, or 2 kPa. To find the force instead, take a hydraulic cylinder with a piston area of 3 square inches operating at 1,000 psi. The force is 1,000 × 3 = 3,000 lbf.
Why does area matter so much?
For the same force, a smaller area gives a higher pressure, and a larger area gives a lower one. Halving the area doubles the pressure. Doubling the area cuts it in half. You can see this in everyday life.
- Knives and needles focus force onto a tiny edge or point.
- Snowshoes and wide tires spread weight so that they don't sink as far.
- Thumbtacks have a broad head for your thumb and a sharp point for the wall.
- Hydraulic machines use a fluid to pass pressure along and multiply force.
Choosing your units
Use units that belong together. Pounds-force divided by square inches gives psi, and newtons divided by square meters gives pascals. If you have an area in square feet or square centimeters, convert it first, as mixing them is the most common cause of a wrong answer. A pascal is very small, so you'll often see kilopascals or bar instead. One bar is 100,000 pascals, or 100 kPa. To change a pressure from one unit to another without a force or area, use our pressure converter.
Gauge pressure and absolute pressure
Gauge pressure is measured relative to the surrounding air. A tire gauge that reads 32 psi is showing how far the pressure inside the tire is above the atmosphere outside. Absolute pressure includes the atmosphere as well. This calculator simply divides a force by an area, so its result is the pressure caused by that force alone. If a problem asks for absolute pressure, you'll need to add the pressure of the atmosphere afterward.
When the force is at an angle
The formula only uses the part of the force that acts straight into the surface, called the normal component. If you push at an angle, part of your effort slides along the surface and doesn't add to the pressure. In that case, work out the perpendicular part before you enter it. For a resting object on a level surface, the normal force is simply its weight.
Finding the area of a round piston
Many pressure problems involve a circular surface, such as a piston, a pipe or the end of a cylinder. Remember to work out the area first. Square the radius and multiply by π. A piston that's 2 inches across has a radius of 1 inch, so its area is about 3.14 square inches. Enter 3.14 in the area box instead of the diameter. Getting this step wrong can change your answer by a large amount, because the area grows with the square of the radius.
Common mistakes
- Mixing units, such as a force in newtons and an area in square inches.
- Using mass instead of force. In metric, multiply kilograms by gravity to get newtons.
- Using the diameter as the area. A circle's area is π × r².
- Confusing gauge and absolute pressure.
Related engineering tools
Change the units with the pressure converter, work out a contact surface using the area and perimeter calculator, and explore motion with the projectile motion calculator.
What next
Use this often? Add Pressure to your Home screen.
Frequently asked questions
What is the formula used by a pressure calculator?
It uses P = F ÷ A, where P is the pressure, F is the force and A is the area.
How do you calculate force from pressure?
Multiply the pressure by the area: F = P × A.
What units does it use?
US mode uses lbf, in² and psi. Metric mode uses N, m² and Pa.
What is 1 psi in kPa?
One psi is about 6.895 kPa.
Does a smaller area increase pressure?
Yes. For the same force, halving the area doubles the pressure.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.