A PCB trace current calculator works out how much current a copper track of a given width can carry for a chosen temperature rise. Enter the width, the copper weight and the rise, choose an outer or inner layer, and you get the maximum current, the cross-section and, with a length, the resistance, voltage drop and power loss at that current.
How to use the pcb trace current calculator
- Choose US or metric units and the layer.
- Enter the trace width.
- Enter the copper weight and the temperature rise you accept.
- Add a length and an ambient temperature for the resistance.
- Press Calculate.
Solving for the current
The tool applies the IPC-2221 relationship directly. The cross-section is the width times the copper thickness, A = W × 1.378 × oz, and the current is I = k × ΔT^0.44 × A^0.725, where A is in square mils and ΔT in °C [1][2]. The step from width and copper weight to area is our own working.
The constants
The constant k is 0.048 for an outer layer and 0.024 for an inner layer [1][2]. The exponents are 0.44 for the temperature rise and 0.725 for the area [1]. One ounce of copper is taken as 1.378 mil thick [2]. Wikipedia gives 34 micrometres, about 1.34 mil, for one ounce per square foot, so the tool is slightly generous on thickness [4]. The result line prints the layer and constants, so you can check the numbers against another source.
A worked example
A 53.82 mil trace of 1 oz copper on an outer layer, with a 10 °C rise, has an area of 74.16 square mils and carries 3 A. A 140 mil inner trace in the same copper and rise also carries about 3 A. A width of 53.8 mil gives 2.999 A, which the tool shows to four digits. These results are our own working from the formula.
Outer and inner layers
An outer trace can lose heat to the air, while an inner one is surrounded by board material. For the same width, copper and rise, the outer layer carries twice the current of an inner one, because k is 0.048 against 0.024 [1][2]. For the same current, the inner trace must be about 2.6 times wider, since 2 to the power 1/0.725 is about 2.6, which is our own working. Pick the layer the trace uses.
Width units
In US mode the width is in mil, which is a thousandth of an inch. In metric mode it is in millimetres, and the tool converts it to mil by dividing by 0.0254. A 1.37 mm track is 53.9 mil. The result shows the width in both units so that you can confirm the conversion. Keep in mind that the etched width of a real track can be a little smaller than the drawn width.
Copper weight
The copper weight box is in ounces per square foot, the unit in which PCB copper is specified [4]. Doubling the weight doubles the thickness and so the area, and the current rises by 2 to the power 0.725, about 1.65 times. The formula was developed for a single copper weight [1]. The tool shows a warning outside 0.5 to 3 oz, a range we chose ourselves, because our sources do not state the tested range.
Temperature rise
The rise is how much hotter you let the trace become than the air around it. The current grows with the rise to the power 0.44, so doubling the rise raises the allowed current by only about 36 percent. In US mode, enter the rise in degrees Fahrenheit, and the tool divides it by 1.8. The tool takes the trace temperature as the ambient plus the rise, which is our assumption, not a stated formula.
Resistance and loss
If you give a length, the tool adds the resistance with R = ρ × L ÷ A′ × (1 + α × (T − 25)), using ρ = 1.7 × 10⁻⁶ ohm cm and α = 0.0039 per °C. Wikipedia gives copper 1.68 × 10⁻⁸ ohm metre, which is 1.68 × 10⁻⁶ ohm cm, and about 3.93 × 10⁻³ per kelvin for annealed copper, with the same linear temperature rule [3]. The tool rounds these figures. The drop and the power are then worked out at the maximum current it found. For the 3 A example over 60 mm at 35 °C, these are 66.45 mV and 0.199 W, which is our own working.
Limits of the method
The formula comes from fitted test data and has limits. Proto Express says that it ignores large ground planes, copper pours and heat sinks, so it may be conservative, and that it was built from a single board type and one copper weight [1]. Wevolver adds that the data came from still air and that stack-up and forced airflow are not covered [2]. IPC-2152 was written to address this by using data from different board designs [1]. The tool does not model vias, board thickness or nearby heat sources.
Using the answer
Treat the current as an upper bound for steady direct current, not as a rating, and keep a margin below it. Short pulses, high frequencies and shared heat from neighbouring parts change the picture, and so do power planes. If a track must carry more, widen it, use thicker copper or add parallel tracks, and check the design with your board maker, who knows the actual process.
Common mistakes
- Entering the drawn width in the wrong unit. Check that mil and millimetres are not mixed.
- Using the outer layer for an inner trace. Inner traces carry less.
- Entering the final temperature as the rise. The rise is the increase over ambient.
- Ignoring the length. A long thin trace loses voltage even if it is cool.
What next
Use this often? Add Pcb Trace Cu to your Home screen.
Frequently asked questions
What is a PCB trace current calculator?
A tool that finds the current a copper track of a given width can carry for a chosen temperature rise, using the IPC-2221 formula.
How much current can a PCB trace carry?
A 53.8 mil trace of 1 oz copper on an outer layer carries about 3 A for a 10 °C rise. An inner trace needs about 140 mil for the same current.
What is the formula for trace current?
I equals k times the rise to the power 0.44 times the area to the power 0.725, with k 0.048 outside and 0.024 inside, and the area in square mils.
Does the rise change the current much?
The current grows with the rise to the power 0.44, so doubling the rise allows about 36 percent more current.
Is the maximum current a rating?
No. It is an estimate that ignores planes, pours and vias. Keep a margin and check the design with your board maker.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.