A mechanical advantage calculator gives the ideal force multiplication of the simple machines. Pick a lever, a pulley, an inclined plane, a wedge, a screw or a wheel and axle, enter its measurements, and you get the mechanical advantage. Add the load to find the effort needed. It also serves as a pulley calculator for a block and tackle.
How to use the mechanical advantage calculator
- Choose the machine.
- Enter its measurements in one length unit.
- Add the load to see the effort force that is needed.
- Press Calculate.
What mechanical advantage means
Mechanical advantage is the factor by which a machine multiplies a force: the output force divided by the input force [1]. A value above 1 means a small effort can move a bigger load, at the cost of moving the effort farther. A value below 1 means the machine trades force for speed or distance. The calculator gives the ideal value, from geometry alone, and says in plain words which of the two the number describes.
The lever
For a lever the ideal mechanical advantage is the ratio of the effort arm to the load arm: the distance from the fulcrum to the input force over the distance from the fulcrum to the output force [1]. The law of the lever is the same ratio, effort arm divided by load arm. With an effort arm of 2 and a load arm of 0.5, in any unit, the advantage is 4. A load of 100 then needs an effort of 25, and the effort moves four times as far.
The pulley and block and tackle
For a block and tackle, Wikipedia states that the ideal advantage equals the number of rope sections that support the moving block [1]. Its example has six sections and a 600 lb load: the ideal effort is 100 lbF, and the rope must be pulled six feet to lift the load one foot [1]. The calculator uses that rule, so you count the supporting sections and enter a whole number. For a pulley calculator job, that is the number to use. A single fixed pulley only changes the direction of the pull, and has an advantage of 1.
Counting pulleys
It is easy to count pulley wheels, but the quantity that matters is the number of rope sections that support the moving block [1]. We use the rope-section count because it is the quantity you can see and count, and it needs no assumption about pairs of wheels.
The inclined plane
For a ramp the advantage is the slope length divided by the vertical rise, which equals one over the sine of the angle of the slope [2]. A ramp 5 units long that rises 1 unit gives an advantage of 5 and an angle of about 11.54 degrees. The effort is a fifth of the load, but the load must be pushed five times as far along the slope as it is raised. The rise cannot exceed the slope length, and the calculator checks for this.
The wedge
A wedge works like two ramps back to back. The calculator uses the length of the sloping side divided by the thickness of the thick end, so a wedge 20 long and 4 thick has an advantage of 5. Wikipedia gives the advantage of a wedge as the length of its slope divided by its width, and says that the longer and thinner the wedge, the more advantage it yields [5]. Check any critical figure with a textbook.
The screw
For a screw, Wikipedia gives MA = 2π r ÷ l, where r is the radius at which the effort is applied and l is the lead [3]. This equals π × diameter ÷ lead. The lead is the distance the screw advances in one full turn, which equals the pitch for a single-start thread. With a diameter of 2 and a lead of 0.5, the advantage is about 12.57. The diameter here is that of the circle around which the effort moves. A wrench or a screwdriver handle moves the effort around a larger circle than the shaft, which raises the advantage; that remark is our own working.
The wheel and axle
For a wheel and axle the advantage is the wheel radius divided by the axle radius [4]. A wheel of radius 0.5 on an axle of radius 0.05 gives 10, so a pull on the rim lifts ten times as much as the same pull on the axle rim would. Use one length unit for both radii; the ratio is dimensionless, so the unit does not matter.
Effort, load and distance
Give a load and the calculator divides it by the advantage to get the effort, as F in = F out ÷ MA, with no friction. In the ideal case the work in equals the work out, so the effort moves MA times as far as the load. That is why the long rope pull or the long ramp is the price of a smaller force.
Limits and safety
Friction, the weight of the rope or the lever, and flex all raise the real effort above the ideal value, sometimes by a large amount for screws and wedges. The numbers are for learning and quick estimates. Do not use them to choose ropes, hooks or hoists for lifting loads, because those need safety factors and ratings that this page does not cover. Have a qualified person check any real lifting arrangement against the rating of every part.
Common mistakes
- Counting pulley wheels instead of rope sections. Count the sections that support the moving block.
- Mixing length units. Enter both arms, radii or lengths in the same unit.
- Ignoring friction. Real machines need more effort than the ideal value.
- Taking the diameter of the screw for the handle. A bigger circle for the effort raises the advantage.
- Using the result to size lifting gear. Check real hardware against its rated load.
What next
Use this often? Add Mechanical A to your Home screen.
Frequently asked questions
What is a mechanical advantage calculator?
A tool that finds the ideal force multiplication of a simple machine from its measurements.
How do you find the mechanical advantage of a pulley?
For a block and tackle, count the rope sections that support the moving block; that number is the ideal advantage.
What is the mechanical advantage of a ramp?
The slope length divided by the vertical rise, which equals one over the sine of the angle.
What is the mechanical advantage of a lever?
The effort arm divided by the load arm.
Is the mechanical advantage real or ideal?
Ideal. Friction makes the real effort larger, so the real advantage is lower.
Can a mechanical advantage be below 1?
Yes. It then trades force for speed or distance, as in tweezers.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.