Saved

Press the star next to a tool's name to save it.

All my tools

Gear Ratio Calculator

Use this gear ratio calculator to find the ratio of a gear train from the number of teeth on its driver and driven gears, up to three stages, with the output speed and torque.

Restored your last values ·

Enter the number of teeth on the driver and the driven gear of each stage. Use more stages for a compound train. Add an input speed and torque to see the output speed and torque of an ideal drive.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the teeth of the first pair of gears, then press Calculate.

See full result

A gear ratio calculator finds the gear ratio of a gear train from the number of teeth on its gears. Enter the driver and the driven gear of up to three stages, and it gives the ratio, the output speed and the output torque. Idler gears that only reverse the direction do not need to be entered.

How to use the gear ratio calculator

  1. Enter the teeth of the first driver and driven gears.
  2. Add more stages for a compound train.
  3. Add an input speed or torque if you want the output.
  4. Press Calculate.

The gear ratio

The angular speed ratio, also known as the gear ratio, of two meshing gears is R_AB = |ω_A| ÷ |ω_B| = r_B ÷ r_A = N_B ÷ N_A, where A is the input gear and N the number of teeth [1]. The ratio is therefore the teeth of the driven gear divided by the teeth of the driver. A driver of 13 teeth turning a gear of 21 has a ratio of 1.615, and the driven gear turns more slowly.

Torque

The torque ratio of the train equals the speed ratio, TR = T_B ÷ T_A = R_AB, which follows from the principle of virtual work, assuming no losses in the engagement of the teeth [1]. A reduction gear multiplies the torque by the same factor as it reduces the speed. An input torque of 100 with a ratio of 10.157 gives an output torque of 1,015.7, in an ideal drive.

Compound trains

In a compound train, with two or more pairs of gears, the total reduction is the product of the reduction of each stage [1]. The calculator multiplies the stages. With stages of 13 to 21 and 21 to 42, the ratios are 1.615 and 2, and the total is 3.231. The page gives the same example, with the total of about 3.23 [1].

Idler gears

An idler is a gear placed between the driver and the driven gear. The page says that the ratio then depends only on the number of teeth on the first and last gear, since the idler's teeth cancel: R = (N_I ÷ N_A)(N_B ÷ N_I) = N_B ÷ N_A [1]. Each idler reverses the direction of rotation of the final gear but does not change the ratio [1]. So you can leave idlers out.

A car example

The page gives the first gear of a sports car: the transmission has a ratio of 2.97 and the final drive 3.42, so the engine turns 2.97 × 3.42 = 10.16 times for each turn of the wheel [1]. In the calculator, enter 1 and 2.97 for the first stage and 1 and 3.42 for the second. At 3,000 rpm, the wheels then turn at 295.35 rpm.

Timing drives

The page notes that in a four-stroke engine, the crankshaft gear has half as many teeth as the camshaft gear, for example 34 and 68, so the camshaft turns at half the speed of the crankshaft [1]. In the calculator, 34 teeth driving 68 give a ratio of 2:1. This ratio keeps the valves in step with the pistons in the cycle of the engine.

Speed increase

A ratio below 1 is an overdrive: the output turns faster than the input, and the torque is less. Enter 40 teeth driving 20 and the ratio is 0.5, so the output turns twice as fast. The calculator names it as a speed increase. Use a speed increase for a generator driven by a slow turbine, and a reduction for a motor that drives a heavy load.

Units

The gears are described by their numbers of teeth, so the ratio does not depend on a unit. The speed is in revolutions per minute and the torque in any unit, with the output in the same unit. For gears that mesh, the teeth must have the same pitch or module. The pitch radius is proportional to the number of teeth, so you can use pitch diameters for the same ratio.

Limits

The calculation is for an ideal train. Each mesh of well-made spur gears loses about 1 to 3 percent of the power, a rough figure of our own, so a train of three stages may lose 5 to 10 percent. The page says that its torque result assumes no losses in the engagement of the teeth [1]. Belts, chains and worm gears have their own efficiencies, which this calculator does not give.

Using the calculator

Enter the driver and driven teeth of the first stage, and add stages for a compound drive. Read the ratio and the direction of the change in speed. Add the input speed and torque to see the output. To find a gear for a target ratio, try tooth counts until the ratio is close, keeping the counts as whole numbers.

Choosing teeth

When you design a gear pair, avoid tooth counts with a common factor, such as 20 and 40, if you want the wear to spread evenly over all the teeth. A pair such as 21 and 42 still has a ratio of 2, but the 20 and 41 pair has the same ratio nearly and wears more evenly. This tip is our own, and it does not change the ratio that the calculator gives.

Common mistakes

  • Swapping the driver and the driven gear. The input is the driver.
  • Counting the idler as a stage. It does not change the ratio.
  • Expecting full torque. Real gears have losses.
  • Using non-integer teeth. Teeth are whole numbers.

What next

Use this often? Add Gear Ratio to your Home screen.

Frequently asked questions

What is a gear ratio calculator?

A tool that finds the speed and torque ratio of a gear train from the teeth of its gears.

What is the gear ratio formula?

R = N_driven ÷ N_driver.

How do I find the ratio of a compound gear train?

Multiply the ratios of the stages.

Does an idler gear change the ratio?

No. It only reverses the direction of rotation.

How does the output torque relate to the ratio?

In an ideal train, the torque is multiplied by the ratio.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools