Saved

Press the star next to a tool's name to save it.

All my tools

Lift Coefficient Calculator

Use this lift coefficient calculator to find C_L from the lift force, wing area, airspeed and air density, or to find the lift force from a known coefficient.

Restored your last values ·

Choose US or metric units. To find the lift coefficient, enter the lift force, the wing area and the speed. To find the lift force, enter the coefficient, the area and the speed. Leave the density blank for sea-level air.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to find, fill in the boxes that show, then press Calculate.

See full result

A lift coefficient calculator turns a measured lift force into the dimensionless coefficient C_L, or turns a known coefficient into the lift force. It uses the lift force, the wing area, the airspeed and the density of the fluid, and it works in US or metric units.

How to use the lift coefficient calculator

  1. Choose US or metric units, then choose to find the coefficient or the force.
  2. Enter the area and the airspeed with the lift force or the coefficient.
  3. Leave the density blank for standard sea-level air, or enter your own.
  4. Press Calculate.

The definition of the lift coefficient

The lift coefficient is C_L = L ÷ (q S), where L is the lift force, S is the relevant surface area and q is the dynamic pressure of the fluid [1]. The dynamic pressure is tied to the fluid density ρ and the flow speed u, and equals ½ ρ u² [1]. Putting them together, C_L = 2 L ÷ (ρ u² S) [1].

The lift force form

Solving the same relation for the force gives L = C_L × ½ ρ V² × S [1]. This is how a designer estimates the lift of a wing from a coefficient taken from tests. The calculator offers both directions, so one page covers the measured case and the predicted case.

First worked example

Take a wing of 1 m² at 100 m/s that produces 800 N in air of density 1.225 kg/m³ [2]. C_L = 2 × 800 ÷ (1 × 1.225 × 100²) = 1,600 ÷ 12,250, which is about 0.1306. Choose metric, type the three values and the density, and the result line shows 0.13061.

Second worked example

The second example finds the force. A wing of 2 m² has C_L = 0.52 at 150 m/s in the same air. The dynamic pressure is 13,781 pascals, and the force is 0.52 × 2 × 13,781 = 14,333 newtons, or 14.33 kN. Switch to the force mode, enter 0.52, 2 and 150 and leave the density blank.

Density

The default density is 1.225 kg/m³, the figure for standard sea-level air [2]. Density changes with altitude, temperature and weather, so a different air density changes the result. The calculator uses 1.225 when the box is blank and says so. For another fluid, such as water, enter its density.

US units

In US mode, you enter pounds-force, square feet, miles per hour and pounds per cubic foot. The calculator converts them to newtons, square metres, metres per second and kilograms per cubic metre before it applies the formula, and it converts the force back. These conversion factors are standard ones and are our own working.

Dynamic pressure

The calculator also reports the dynamic pressure q = ½ ρ V². In metric mode it is in pascals, and in US mode it is in pounds-force per square foot. Because it is the same pressure that appears in the lift and drag formulas, it is a handy figure to compare between speeds. Doubling the speed multiplies it by four.

Why the coefficient depends on the wing

A given C_L belongs to one cross-section of the wing, which is its airfoil shape, and to one flight condition [1]. It also changes with the angle of attack. So you should not apply a coefficient measured on one wing to another design. Lift depends on the speed, the air density and the wing area, so a higher speed can offset a heavier load, as L = C_L × ½ ρ V² × S shows.

Stall speed

An aircraft that flies below its stall speed cannot make enough lift for level flight, whatever coefficient the calculation gives. The calculator does not model stall. If the coefficient you compute is larger than any real wing can reach, the airspeed in your example is too low for the weight.

Where to use it

Use the tool for physics homework, for a model aircraft estimate, for a wind tunnel measurement, or to see how lift scales with speed. It is not a design tool for a real aircraft. Always get the design checked by a qualified aerospace engineer and follow the applicable rules.

Reading a coefficient

Typical values depend on the wing and the flight condition, so the calculator does not judge a result as good or bad. Compare the figure with the data for your airfoil, if you have it. A coefficient that is far above the published maximum for the shape suggests that the force, the area or the speed was entered wrongly, or that the units were mixed.

How speed changes lift

Because lift grows with the square of the speed, doubling the speed with the same wing and coefficient gives four times the force. The calculator makes this easy to see: run the force mode at two speeds and compare the results. The same square law applies to the dynamic pressure, which the calculator shows below the main result.

Common mistakes

  • Mixing US and metric values. Choose one system before entering the numbers.
  • Using the wrong area. Use the reference area that the coefficient was defined for.
  • Using sea-level density at altitude. Enter the real density.
  • Treating C_L as a constant of the aircraft. It changes with the angle of attack.

What next

Use this often? Add Lift Coeffic to your Home screen.

Frequently asked questions

What is a lift coefficient calculator?

A tool that finds the dimensionless coefficient C_L from a lift force, a wing area, an airspeed and a fluid density, or the force from the coefficient.

What is the lift coefficient formula?

C_L = 2 L ÷ (ρ V² S), where L is the lift, ρ the density, V the speed and S the area.

What air density does the calculator use?

1.225 kg/m³, standard sea-level air, when you leave the box blank.

Does the lift coefficient have units?

No, it is dimensionless.

Can I use it for water?

Yes, enter the density of water, and the same formula applies to any fluid.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools