Saved

Press the star next to a tool's name to save it.

All my tools

Internal Resistance Calculator

Use this internal resistance calculator to find the resistance inside a battery or cell from its no-load voltage, the loaded voltage, the load resistance or the current, with the voltage lost inside.

Restored your last values ·

Choose what you measured. Enter the no-load voltage or EMF of the battery, and either the load resistance and current, or the loaded voltage with the load resistance or the current. You get the internal resistance.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what you know, fill in the boxes and press Calculate.

See full result

An internal resistance calculator finds the resistance inside a battery or cell from measurements of its no-load voltage and what it delivers to a load. Choose what you measured, enter the values and read the internal resistance, the terminal voltage and the voltage lost inside the cell.

How to use the internal resistance calculator

  1. Choose what you know.
  2. Enter the no-load voltage and the other values, in volts, ohms and amperes.
  3. Press Calculate.

What internal resistance is

Internal resistance is the resistance that the electrolyte and electrodes of a battery offer to the flow of current. It rises as a battery ages [1]. A source can be modelled as an ideal voltage source in series with an internal resistance, so the terminal voltage falls below the no-load value by the drop across that resistance [1].

The basic relations

For a cell of EMF ε with internal resistance r and a load R, the total resistance of the circuit is R_T = r + R, the current is I = ε ÷ (R + r), the internal resistance is r = ε ÷ I − R, and the terminal voltage is V = ε − I · r. These follow from Ohm's law applied to the series circuit. Here ε is the EMF, R the load resistance and r the internal resistance. The first mode of the calculator uses r = ε ÷ I − R directly.

A worked example

Take an EMF of 3 volts, a load of 995 ohms and a current of 3 milliamperes, which is 0.003 amperes. Then r = 3 ÷ 0.003 − 995 = 1000 − 995 = 5 ohms, and the terminal voltage is 3 − 0.003 × 5 = 2.985 volts. The calculator starts with these values in its boxes, so you can press Calculate and see the 5 ohms.

From the loaded voltage and the load

If you measured the no-load voltage and the voltage under a known load, Wikipedia gives r = (V no-load ÷ V loaded − 1) × R_load [1]. With 3 volts, 2.985 volts and 995 ohms, r = (3 ÷ 2.985 − 1) × 995 = 5 ohms, the same answer as before. This is the voltage-and-load method that Wikipedia lists for measuring the resistance of a cell.

From the voltage drop and the current

If you know the current instead of the load, rearrange V = ε − I · r into r = (ε − V) ÷ I. This rearrangement is our own algebra from the terminal voltage formula. With 3 volts, 2.985 volts and 3 milliamperes, r = 0.015 ÷ 0.003 = 5 ohms. The three modes give the same result for the same circuit, which is a good check.

Terminal voltage and current

A cell delivers its full EMF only when no current flows. As the current rises, the terminal voltage drops, and a smaller internal resistance gives a larger terminal voltage [1]. The calculator shows the current, the terminal voltage, the voltage lost inside the cell and the heat power I² × r lost inside it, so you can see how much of the energy is wasted in the cell.

Measuring it in practice

Measure the no-load voltage with a high-resistance meter, then connect a known load and measure the voltage across the cell again, as Wikipedia describes [1]. Take the second reading quickly, since the voltage sags as the cell warms and discharges. A bigger load current gives a bigger voltage drop, which is easier to read, but a small cell may be harmed by a heavy load.

Meters and frequency

An AC milliohm meter or ESR meter can also estimate the internal resistance of a battery. Such readings depend on the test frequency, so they are best used to compare cells measured the same way, not as a precise DC value.

Errors the calculator catches

The loaded voltage cannot be higher than the no-load voltage, so the calculator gives a message when it is. A negative internal resistance is also impossible for a real cell, and it usually means a wrong reading: in the first mode, for example, the current would have to be below the EMF divided by the load. Check the values and the units, especially milliamperes against amperes.

Using the calculator

Pick the mode that matches what you measured, enter the values, and press Calculate. Compare a new cell with an old one under the same load to see how much the internal resistance has grown. A high value means a large voltage drop and wasted heat at the same current. The calculator uses a simple series model, so treat the result as an estimate.

What the result tells you

The internal resistance sets the largest current that a cell can supply without its terminal voltage falling too far. A cell of 3 volts and 5 ohms, shorted through almost no resistance, could give at most 0.6 amperes in this simple model, which is our own working from I = ε ÷ r. Real cells also heat up and change, so use the figure to compare cells rather than to predict a short circuit.

Cells in a pack

When cells are connected in series, their internal resistances add up, and in parallel the combined value falls. These are standard rules for resistors that we apply here as our own working. Use the calculator on one cell at a time, and then combine the values to estimate the resistance of the whole pack, remembering that the connections add some resistance of their own.

Common mistakes

  • Entering milliamperes as amperes. 3 mA is 0.003 A.
  • Using the loaded voltage as the EMF. The EMF is measured with no load.
  • Measuring the load resistance with the cell connected. Measure it separately.
  • Assuming the value is constant. It changes with charge and age.

What next

Use this often? Add Internal Res to your Home screen.

Frequently asked questions

What is an internal resistance calculator?

A tool that finds the resistance inside a battery from voltage and load measurements.

What is the formula for internal resistance?

r = ε ÷ I − R, or r = (V no-load ÷ V loaded − 1) × R.

How do I find internal resistance from the voltage drop?

Divide the drop between the no-load and loaded voltage by the current.

Why does the terminal voltage fall under load?

Part of the EMF is dropped across the internal resistance, I times r.

Does internal resistance change?

Yes, it is low in a new battery and rises with use.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools