An inclined plane calculator splits the weight of a block on a slope into the part along the slope and the part pressing into it. Enter the mass and the angle to get the normal force, the force along the slope, the acceleration and the ideal mechanical advantage. Add friction and a height for the sliding time.
How to use the inclined plane calculator
- Enter the mass in kilograms and the angle in degrees.
- Add a friction coefficient if the slope is not smooth.
- Add the height to get the slope length and the sliding time.
- Press Calculate.
Two components of the weight
The weight of a block is F_g = m × g. It splits into a component along the slope, F_i = F_g × sin θ, and a component perpendicular to the slope, F_n = F_g × cos θ [1]. The first pulls the block down the slope, and the second presses it into the surface [1]. At a steeper angle, more of the weight pulls along the slope.
The normal force
The normal force is the force with which the slope pushes back on the block, at right angles to the surface [2]. On a slope with no other forces, it equals F_g × cos θ [2]. This is the Normal Force Calculator that people look for: enter the mass and the angle, and read the normal force. On a flat surface the angle is 0 and the normal force is the whole weight.
Friction
The friction force is the friction coefficient times the normal force, F_f = f × F_n [3], and the net force along the slope is F_i − F_f. Because the normal force falls as the slope steepens, friction becomes weaker at steeper angles. Leave the friction box blank for a smooth slope. The calculator uses one coefficient, so it does not separate static from sliding friction.
Acceleration
Dividing the net force by the mass gives the acceleration down the slope, a = g × (sin θ − f cos θ) [1]. The mass cancels, so the acceleration does not depend on it. For a smooth slope, a = g × sin θ, and at 90 degrees the block falls freely with a = g. The calculator reports the acceleration in metres per second squared.
When the block does not slide
The net-force formula applies only when the angle is greater than the friction angle, where tan of the friction angle equals f [1]. Otherwise the block stays at rest. With f = 0.5 the limit is about 26.57 degrees, so a 20 degree slope does not move the block. The calculator says so, instead of showing a negative acceleration.
Mechanical advantage
Wikipedia gives the ideal mechanical advantage of an inclined plane, with no friction, as 1 ÷ sin θ, which also equals the length of the slope divided by its rise [1]. At 40 degrees that is 1.5557, so pushing a load up the slope takes about 64 percent of the force of lifting it straight up.
Pushing up the slope
To move a block up the slope at a steady speed, the push has to balance the part of the weight along the slope and the friction, F_i + F_f. This is our own working from the formulas above, and it ignores any starting jolt. For the example of 2 kilograms at 40 degrees with a coefficient of 0.2, it is about 15.6 newtons, less than the 19.6 newtons needed to lift the block straight up.
Slope length and sliding time
Given the height H, the length of the slope is L = H ÷ sin θ, and starting from rest the sliding time is the square root of 2L ÷ a, after which the speed is a × t. These follow from geometry and constant acceleration, so they are our own working. The energy lost to friction is m × g × H − m × V² ÷ 2, from energy conservation, which is also our own working. The calculator assumes the block starts at rest at the top.
A worked example
Take 2 kilograms on a slope of 40 degrees, with a coefficient of 0.2 and a height of 5 metres. With g = 9.80665 the calculator gives a normal force of 15.025 newtons, a force along the slope of 12.607 newtons, an acceleration of 4.8011 and a sliding time of 1.8 seconds. Rounding g to 9.807 would change the last digits slightly.
Limits
The calculator treats the block as a point on a rigid, flat slope. It does not cover rolling objects, which accelerate more slowly because some of the energy goes into spinning, nor air resistance or a push already acting on the block. For a ramp to be built, ask an engineer to check it. The value of g is the standard one, 9.80665 metres per second squared [4].
Choosing the angle
The angle is the one between the slope and the horizontal. If you know the rise and the run instead, the angle is the inverse tangent of the rise divided by the run, a standard relation that we state as our own working. A 1 in 12 ramp, for example, is about 4.8 degrees. At such a gentle angle, the force along the slope is only about 8 percent of the weight, which is why long ramps make loads easy to move.
Reading the results together
The normal force and the force along the slope always add up, as vectors at right angles, to the whole weight. You can check the numbers: the squares of the two forces sum to the square of the weight. If you raise the angle, the normal force falls and the force along the slope grows, until at 90 degrees the slope carries none of the weight.
Common mistakes
- Using the angle in radians. Enter degrees.
- Treating the normal force as the full weight. It is the weight times cos θ.
- Expecting motion at any angle with friction. Check the friction angle.
- Forgetting that the mass cancels. Acceleration does not depend on mass.
What next
Use this often? Add Inclined Pla to your Home screen.
Frequently asked questions
What is an inclined plane calculator?
A tool that finds the forces, the acceleration and the mechanical advantage of a block on a slope.
How do I find the normal force on a slope?
Multiply the weight m times g by the cosine of the angle.
What is the acceleration down an incline?
a = g × (sin θ − f cos θ), where f is the friction coefficient.
What is the mechanical advantage of an inclined plane?
Ideally 1 divided by sin θ, the slope length divided by the rise.
When does a block not slide?
When the friction coefficient is at least the tangent of the angle.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.