Saved

Press the star next to a tool's name to save it.

All my tools

Hoop Stress Calculator

Use this hoop stress calculator to estimate the circumferential and longitudinal stress in a thin-walled cylinder or sphere from pressure, diameter and wall thickness.

Restored your last values ·

Choose a cylinder or a sphere. Enter the internal gauge pressure, the inside diameter and the wall thickness in the same length unit. Joint efficiencies are optional and default to 1.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose the shape, enter the pressure, diameter and wall thickness, then press Calculate.

See full result

A hoop stress calculator gives the circumferential stress in the wall of a thin-walled cylinder or sphere under internal pressure, the longitudinal stress, and a check that the wall really is thin. It is a learning tool: real pressure equipment needs a code-based design by a qualified engineer.

How to use the hoop stress calculator

  1. Choose a cylinder or a sphere.
  2. Enter the internal gauge pressure, the inside diameter and the wall thickness.
  3. Add a joint efficiency if the wall is welded or riveted, then press Calculate.

What hoop stress is

Hoop stress is the stress in the circumferential direction of the wall of a pipe, tank or sphere, as the pressure inside tries to split it open [1]. The stress along the length of a cylinder is the longitudinal or axial stress [1]. For a thin wall, both are treated as uniform across the thickness, which makes the equations simple and fast to use.

The cylinder equations

For a thin-walled cylinder the Wikipedia page gives the hoop stress as pr ÷ t and the longitudinal stress as pr ÷ 2t, with p the internal gauge pressure, r the inner radius and t the wall thickness [1]. In terms of the diameter d = 2r, the hoop stress is pd ÷ 2t. So the hoop stress is twice the longitudinal one, which is why a pipe that is overloaded usually splits along its length.

The sphere equation

For a sphere, the stress is the same in every direction along the wall: pr ÷ 2t, from the Wikipedia pages [1][2], or pd ÷ 4t with the diameter. A sphere carries a pressure with half the hoop stress of a cylinder of the same diameter, pressure and wall thickness, which is why gas is often stored in spheres. The tool shows the single value in both lines of its answer.

Joint efficiency

Welded or riveted seams are weaker than the plate. Pressure vessel codes handle seams with a joint efficiency, which appears in the denominator of the wall equations [1]. The tool uses η in the same way: pd ÷ (2tη) for the hoop stress in a cylinder, pd ÷ (4tη) for the longitudinal stress, and pd ÷ (4tη) for the sphere. Leave the boxes blank for a seamless wall, which means η = 1. An efficiency of 0.5 doubles the stress.

The worked example

Take a riveted water tank in the form of a sphere: pressure 1.5 MPa, diameter 3 m, thickness 16.667 mm and efficiency 0.75. By hand, 1.5 × 3000 ÷ (4 × 16.667 × 0.75) is about 90 MPa. Enter 1.5, 3000, 16.667 and 0.75 in metric mode with the sphere shape, and the tool shows 89.998 MPa, which is 90 MPa after rounding the thickness. For a pipe of 1,000 mm diameter and 10 mm wall at 2 MPa, the hoop stress is 100 MPa.

When is a wall thin?

The Wikipedia page says that a vessel can be considered thin-walled if its diameter is at least 10 times, and sometimes 20 times, its wall thickness [1]. The Hoop stress article treats a wall as thin when it is no more than about one tenth of the radius [2], which is a diameter of 20 times the thickness. The tool reports d ÷ t and tells you which rule you pass. Below a ratio of 10, a thick-wall analysis is needed and these results are not reliable.

Radial stress

The pressure pushes on the inner surface and the outer surface is at atmospheric pressure, so the stress through the wall varies from the pressure on the inside to zero outside. In the thin-wall model this radial stress is small next to the hoop stress and is ignored. The Hoop stress article treats the radial stress as negligible next to the hoop and axial stresses in a thin wall [2], so this tool does not compute it.

Pressure and stress units

In US mode the pressure is in psi and the lengths are in inches, so the stress comes out in psi. In metric mode the pressure is in MPa and the lengths in millimetres, so the stress is in MPa. Each result also shows the other unit, using 1 psi = 0.00689475729 MPa, a standard factor that is our own addition. The diameter and thickness must use the same length unit, as only their ratio matters.

Using the result

Compare the hoop stress with the allowable stress that a code gives for the material at the working temperature, which includes a safety factor. This calculator does not know the material and does not make that comparison, so it cannot say that a vessel is safe. It also ignores the end caps, nozzles, supports, corrosion allowance and fatigue, all of which an engineer must include.

A note on safety

Pressure vessels store a great deal of energy, and a failure can injure people. Use this page to understand how pressure, size and wall thickness are related and to check a hand calculation. Do not use it to choose the wall of a real vessel, pipe or tank, and do not use it to approve a repair. Ask a qualified engineer and follow the pressure equipment code that applies where you work.

Common mistakes

  • Using the outer diameter. The equations use the inside diameter.
  • Different units for diameter and thickness. Use inches with inches or millimetres with millimetres.
  • Entering absolute pressure. Use gauge pressure, the pressure above the atmosphere.
  • Treating a thick wall as thin. Check d ÷ t first: below 10 the equations do not apply.

What next

Use this often? Add Hoop Stress to your Home screen.

Frequently asked questions

What is a hoop stress calculator?

It estimates the circumferential stress in the wall of a thin-walled cylinder or sphere that holds an internal pressure.

What is the hoop stress formula for a cylinder?

Hoop stress equals the pressure times the diameter divided by twice the wall thickness, with a joint efficiency in the denominator if there is a seam.

Why is hoop stress twice the longitudinal stress?

In a closed cylinder the circumferential wall carries the pressure over the length, while the end caps load the ring section, giving half the stress along the axis.

When can I treat a wall as thin?

When the diameter is at least 10 times, and more safely 20 times, the wall thickness.

Can I use it to size a real pressure vessel?

No, it is an educational estimate; real vessels need a code-based design by a qualified engineer.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools