A guitar string tension calculator finds how hard a string is pulled when it is tuned to a given note. Pick the string and its gauge, the note and the scale length, and it gives the tension in pounds-force, newtons and kilograms-force. It can also work backwards from a tension to a unit weight.
How to use the guitar string tension calculator
- Choose US or metric units.
- Pick the string type and enter the gauge in thousandths of an inch.
- Choose the pitch of the open string, or enter a frequency.
- Enter the scale length and press Calculate.
The law behind it
The tension in a string follows from Mersenne's law for a vibrating string. The frequency is f = (1 ÷ 2L) × √(T ÷ μ), where L is the length that vibrates, T the tension and μ the mass per unit length [2]. Turn it round and the tension is T = (2 L f)² × μ, with a conversion constant for the units. Doubling the frequency makes the tension four times as great. The Mersenne's laws page says that a tension of 10 pounds must become 40 pounds for a note an octave higher [2].
The constant in pounds
Unit weight is often given in pounds per inch, so the formula needs a constant to turn pound-mass into pound-force. We use 386.08858 inches per second squared, which is standard gravity of 9.80665 metres per second squared divided by 0.0254 metres to the inch, and write the formula as T = (f × 2 × L)² × μ ÷ g. This constant is not gravity as such, but a unit conversion, and the arithmetic is our own working.
Where the unit weights come from
The unit weights are the D'Addario figures in the EverTune tension chart, which lists a unit weight for each string code, such as 0.00002215 for a plain steel .010 [1]. The calculator holds the weights of 22 plain steel strings from .007 to .026, and nickel-plated and stainless round wound strings. The chart notes that D'Addario supplies unit weights and tensions for its electric guitar strings [1].
A worked example
Take a plain steel .010 string with a unit weight of 0.00002215 pounds per inch, tuned to 329.6 hertz on a scale length of 25.5 inches. Then 2 × 25.5 × 329.6 is 16,809.6, and its square times 0.00002215 divided by 386.08858 gives 16.21 pounds. This is our own working. With the exact equal-tempered E4 of 329.63 hertz, the result is 16.213.
Typical tensions
Tension differs from string to string in a set. A nickel-plated .046 string tuned to E2, which is 82.41 hertz, gives 17.48 pounds on the same scale by our calculation. A .009 plain steel string on E4 gives 13.13 pounds.
Scale length matters
The same string is under less tension on a shorter scale. A plain steel .010 tuned to E4 has 16.21 pounds on a scale of 25.5 inches and 15.27 pounds on 24.75 inches, which is our calculation. For this reason, guitars with different scale lengths feel different with the same set. The tension is proportional to the square of the scale length, so a small change in length has a visible effect.
Pitch and the note list
The notes in the list are the open strings of a standard guitar: E2, A2, D3, G3, B3 and E4. The frequencies come from equal temperament with A4 at 440 hertz, so E4 is 329.63 hertz. This is our own working, and it is why the answer differs a little from one that uses 329.6. Choose your own frequency for a different tuning, such as a drop tuning or a capo.
Using your own unit weight
If your strings are not in the table, because they are another make, another type or a bass or classical string, choose your own unit weight and enter it in pounds per inch. Makers publish these values. The EverTune chart says that actual notes may vary by up to 3.5 percent because of manufacturer variance in string mass [1]. Your own value gives the tension for that string, and the result is no better than the value that you enter.
Working backwards
Choose the unit weight option to start from a tension. Enter the tension you want, the pitch and the scale length, and the calculator gives the unit weight that produces it, using μ = T × g ÷ (2 L f)². Compare that value with a table to pick a gauge. In metric mode, the tension is in newtons, and the unit weight is also shown in kilograms per metre, using 1 pound per inch as 17.858 kilograms per metre.
Limits and safety
The tension is for the string at its tuned pitch. It is not a limit, and a string can break below or above it for other reasons. The calculator does not cover classical nylon strings or bass strings, and the gauges are limited to those in the chart. Check the maker's own tension charts for guidance, and use the result only to compare gauges and scale lengths.
Common mistakes
- Entering the gauge in inches. Use thousandths, so 10 means .010.
- Mixing the scale length units. Use centimetres in metric mode.
- Using the wrong string type. A wound .046 is much heavier than a plain .046.
- Reading it as a safe limit. It is only the tension at the tuned pitch.
What next
Use this often? Add Guitar Strin to your Home screen.
Frequently asked questions
What is a guitar string tension calculator?
A guitar string tension calculator finds the pull on a string from its unit weight, its pitch and its scale length.
What is the formula for string tension?
T = (2 L f)² × μ ÷ g, where L is the length, f the frequency, μ the unit weight and g is 386.08858 inches per second squared for pounds.
How much tension is on a high E string?
A plain steel .010 string at E4 on a 25.5 inch scale has about 16.2 pounds.
Does scale length change the tension?
Yes. The tension varies with the square of the length, so a shorter scale gives a lower tension for the same string and note.
Can I use strings that are not in the list?
Yes. Choose my own unit weight and enter the value in pounds per inch from the maker.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.