The grout calculator works out how much tile grout to buy. Enter the tiled area, the length and width of the tiles, and the width and depth of the grout joints, and it calculates the volume of the joints, converts it to pounds with a typical sanded grout density, adds a waste allowance and tells you how many bags to buy. For example, 100 sq ft of 12 × 12 inch floor tile with 1/8 inch joints 3/8 inch deep takes about 7.6 lb of grout, or 8.3 lb with 10% extra, so one 25 lb bag is plenty.
The grout formula
Grout fills the joints between tiles, so the amount depends on how much joint there is per square foot and how big each joint is. A tile that is L inches long and W inches wide has (L + W) ÷ (L × W) inches of joint per square inch of floor, because each tile shares half of its four edges with its neighbors. So:
- Grout volume = area × joint width × joint depth × (L + W) ÷ (L × W)
- Grout weight = volume × density
The calculator uses 116 lb per cubic foot (1,860 kg per cubic meter), the wet density LATICRETE lists for its 1500 Sanded Grout. You can change it to the figure for your product.
How to use the grout calculator
- Choose US or metric units. US uses square feet and inches; metric uses square meters and millimeters.
- Enter the area you are tiling.
- Enter the tile length and width.
- Enter the joint width (the gap between tiles) and the joint depth, which is usually the tile’s thickness. Fractions like 1/8 work.
- Set the waste allowance and bag size, then press Calculate.
Worked examples
Bathroom floor: 100 sq ft of 12 × 12 inch tile, 1/8 inch joints, 3/8 inch deep. Joint per square inch is (12 + 12) ÷ 144 = 1/6, so the volume is 100 × 144 × 0.125 × 0.375 × 1/6 = 112.5 cubic inches, or 0.065 cubic feet. At 116 lb per cubic foot that’s 7.55 lb, or 8.31 lb with 10% waste: one 25 lb bag.
Subway tile backsplash: 50 sq ft of 3 × 6 inch tile with 1/16 inch joints 1/4 inch deep needs about 4.15 lb with 10% waste. Small tiles have many more joints per square foot, which is why a backsplash can use as much grout per square foot as a large floor.
Metric: 10 sq m of 300 × 300 mm tile with 3 mm joints 10 mm deep needs 2 liters of grout, about 3.72 kg before waste, or 4.1 kg with 10% extra.
How wide should grout joints be?
Custom Building Products’ technical bulletin on grout joint width explains the industry rules. ANSI A108.02 says a grout joint should never be less than 1/16 inch. The actual joint should be about three times the variation in the tile’s face size, so tiles that vary by 1/8 inch need 3/16 inch joints. The Tile Council of North America (TCNA) recommends at least 1/8 inch for rectified tile and 3/16 inch for calibrated tile, plus any edge warping. Joints that are too narrow can’t be filled properly, and the grout may cure powdery or discolored.
Sanded or unsanded grout?
Sanded grout contains fine sand, which makes it stronger in wider joints and less likely to shrink and crack. Unsanded grout is smoother and is used for very narrow joints and for surfaces that sand could scratch, such as some polished stone and glass tile. Check the grout bag for the joint widths it is made for, and follow the tile maker’s advice for delicate surfaces.
Why add waste?
Some grout is always left in the bucket, on the float and in the sponge, and joints are rarely perfectly even. A small job also needs enough grout to mix properly, which is why the calculator rounds the bags up. The waste box starts at 10%; raise it for rough or uneven tile and for your first tiling job.
Tips for grouting
- Mix only what you can use before it starts to stiffen, following the bag’s directions.
- Press grout fully into the joints with a rubber float held at an angle.
- Clean the surface with a damp sponge before the grout hardens, rinsing often.
- Buy one batch for the whole job so the color matches.
Why small tiles need more grout
The amount of joint per square foot depends on the size of the tiles. A square foot of 12 × 12 inch tile has 2 ft of joint running through it, while a square foot of 1 × 1 inch mosaic has 24 ft. That is twelve times as much joint for the same floor, so mosaics and small backsplash tiles use far more grout per square foot. Try a few tile sizes in the calculator to see how quickly the pounds add up.
Wall tile vs. floor tile
Wall tiles are usually thinner than floor tiles, so their joints are shallower and need less grout per foot of joint. Enter the actual thickness of your tile as the joint depth. If the tile sits in a thick bed of thinset, the joint may be slightly shallower than the tile, but using the tile’s thickness gives a safe estimate that won’t leave you short.
Work out the tiles first with the tile calculator, and measure an odd-shaped room with the square footage calculator.
What next
Use this often? Add Grout to your Home screen.
Frequently asked questions
How does the grout calculator work out how much grout I need?
It multiplies the area by the joint width, joint depth and (tile length + tile width) ÷ (tile length × tile width) to get the joint volume, then converts that to pounds and bags.
How much grout do I need for 100 square feet?
For 12 × 12 inch tile with 1/8 inch joints 3/8 inch deep, about 7.6 lb, or 8.3 lb with 10% waste. Smaller tiles and wider joints need more.
What is the minimum grout joint width?
ANSI A108.02 says never less than 1/16 inch. TCNA recommends at least 1/8 inch for rectified tile and 3/16 inch for calibrated tile.
How deep is a grout joint?
Usually about the thickness of the tile, as the grout fills the joint from the setting bed to the tile surface.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.