Saved

Press the star next to a tool's name to save it.

All my tools

Fan Laws Calculator

Use this fan laws calculator to find how the flow, pressure and power of a fan or pump change with its speed, impeller diameter and fluid density, from the affinity laws.

Restored your last values ·

Enter the original and the new speed of the fan or pump. Add the diameters of the two impellers, or the densities of the two fluids, if they change. Add the original flow, pressure and power to get the new values.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the two shaft speeds, then press Calculate.

See full result

A fan laws calculator applies the fan and pump affinity laws to predict how the flow, the pressure and the power of a fan change when its speed, its impeller diameter or the density of the fluid changes. Enter the old and new speeds, and optionally the diameters and densities, and the original flow, pressure and power.

How to use the fan laws calculator

  1. Enter the original and new speeds.
  2. Add the diameters or densities if they change.
  3. Add the original flow, pressure and power.
  4. Press Calculate.

The affinity laws

The affinity laws relate the performance of a fan or a pump at two operating conditions. The page gives them as ratios: the volume flow Q₁ ÷ Q₂ = (n₁ ÷ n₂)(D₁ ÷ D₂)³, the pressure or head gain ΔP₁ ÷ ΔP₂ = (ρ₁ ÷ ρ₂)(n₁ ÷ n₂)²(D₁ ÷ D₂)², and the power W₁ ÷ W₂ = (ρ₁ ÷ ρ₂)(n₁ ÷ n₂)³(D₁ ÷ D₂)⁵ [1]. Here n is the shaft speed, D the impeller diameter and ρ the density.

Speed only

When only the speed changes, the laws are simple: the flow is proportional to the speed, the pressure to its square and the power to its cube. These simple forms are our own reading of the formulas, since the page does not state them separately. Raising the speed from 1,000 to 1,200 rpm, a ratio of 1.2, raises the flow by 1.2, the pressure by 1.44 and the power by 1.728.

The cube law

The power rises with the cube of the speed, so a small change in speed has a large effect on the power. Cutting the speed by 20 percent cuts the power to 51 percent of its value, as 0.8³ = 0.512. This is why variable speed drives save so much energy on fans that do not have to run at full flow. The calculator shows the power ratio directly.

Changing the impeller

If the impeller is changed to another diameter, the flow changes as the cube of the diameter ratio, the pressure as the square and the power as the fifth power [1]. An impeller 25 percent larger, 500 instead of 400 millimetres, at the same speed, gives 1.953 times the flow, 1.5625 times the pressure and 3.05 times the power. Enter both diameters in the same unit.

Density

The pressure and the power are proportional to the density of the fluid [1]. A fan that moves hot air, which is less dense, develops less pressure and needs less power. If the density falls from 1.2 to 1.0 kilograms per cubic metre, the pressure and the power fall to 83 percent of their values, at the same speed and flow. Enter both densities in the same unit.

A worked example

A fan runs at 1,000 rpm and gives 500 units of flow, a pressure of 250 units and takes 2 units of power. At 1,200 rpm, the calculator gives a flow of 600, a pressure of 360 and a power of 3.456. The units are those of your own data. The example is our own, and it shows the pressure and the power rising faster than the flow.

Assumptions

The page says that the laws assume that the efficiency of the pump or fan stays constant, which is rarely exact but can be a good approximation [1]. It also says that the only requirement is that the two machines be dynamically similar, and that the laws apply to centrifugal and axial flows [1]. The page also calls their span of validity limited in practice, so treat the results as a first estimate.

Systems

The laws give the new operating point on a similar curve, but where the fan actually runs depends on the system that it feeds. A duct or pipe has a resistance that rises as the square of the flow. If the system is fixed, the real flow follows the system curve. The calculator gives the scaling of the fan curve, and you must combine it with the system curve.

Limits

The laws are approximate, and they fail for large changes in speed or size, and when the Reynolds number changes a lot. For a major change, use the maker's data. The calculator also does not give the efficiency, and the power it gives is the shaft power if you enter the shaft power. For the electrical power, divide by the efficiency of the motor and the drive.

Using the calculator

Enter the speeds, and add the other changes that apply. Read the factors for flow, pressure and power. Add the original values to see the new ones directly. For a speed change, try a few values: you will see the cube law at work. Check that the new speed is within the limits of the fan and the motor before you rely on the result.

Saving energy with speed control

Many fans run at full speed and have their flow cut by dampers. Reducing the speed instead, with a variable speed drive, lowers the power with the cube of the speed. At 80 percent of the flow, the power is about 51 percent, and at 50 percent flow, only 12.5 percent. The calculator shows these numbers, which is why speed control is one of the most effective ways to save electricity in ventilation.

Common mistakes

  • Forgetting that power rises with the cube. Small speed changes matter.
  • Using different units for two diameters. Use the same unit.
  • Ignoring the system curve. The fan runs where the curves meet.
  • Using large changes. The laws are approximate.

What next

Use this often? Add Fan Laws to your Home screen.

Frequently asked questions

What is a fan laws calculator?

A tool that predicts how a fan's flow, pressure and power change with its speed or size.

What are the fan laws for speed?

Flow is proportional to speed, pressure to its square and power to its cube.

What happens to power if the speed falls 20 percent?

It falls to about 51 percent.

How does the impeller diameter matter?

Flow goes with D³, pressure with D² and power with D⁵.

Do the laws assume constant efficiency?

Yes, and that the machines are dynamically similar.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools