A Darcy's law calculator finds the flow of a fluid through a porous material such as soil, sand or rock, from its permeability, the cross-section area, the pressure drop and the length of the flow path. It also gives the Darcy flux, the flow per unit area, and the hydraulic conductivity.
How to use the Darcy's law calculator
- Choose US or metric units.
- Enter the permeability, area, pressure drop and length.
- Add the viscosity if the fluid is not water.
- Press Calculate.
The law
Darcy's law says that the flow rate through a porous medium is Q = k A Δp ÷ (μ L), where k is the permeability, A the cross-sectional area, μ the dynamic viscosity of the fluid, L the length and Δp the pressure difference [1]. The page notes the minus sign in the flux form, which follows the convention that fluids flow from high pressure to low pressure [1]. The calculator gives the size of the flow.
Darcy flux
The Darcy flux q is the flow rate divided by the area, Q ÷ A, in metres per second [1]. The page says that it is not the velocity at which the fluid actually travels through the pores. That velocity is higher: q = φ u, where φ is the porosity [1]. The calculator gives the flux, and you can divide it by the porosity to get the pore velocity.
Permeability units
The permeability is in square metres in the SI system. The darcy is a unit often used for rocks and soils. One darcy is 9.869233 × 10⁻¹³ square metres, a conversion of our own, since the page lists the darcy but does not give its value. A millidarcy is a thousandth of that. Sand has a permeability of the order of darcies, and tight rock of microdarcies.
A worked example
A sample of 1 darcy, 1 square centimetre in cross-section and 10 centimetres long, with a pressure drop of 101.325 kilopascals, and water-like fluid of 1 millipascal second, passes 10⁻⁷ cubic metres per second, which is 6 millilitres per minute. The Darcy flux is 10⁻³ metres per second, 1 millimetre per second. This example is our own calculation from the formula.
Viscosity
The flow is inversely proportional to the viscosity. A fluid ten times as viscous, such as a light oil of 10 millipascal seconds, flows ten times more slowly through the same sample. Enter the viscosity of your fluid in millipascal seconds, which is the same as centipoise. Water at 20 degrees Celsius has about 1.0, and the calculator uses 1 if you leave the box blank.
Hydraulic conductivity
In hydrogeology, the flow is often written with the hydraulic conductivity K, which depends on the fluid as well: K = k ρ g ÷ μ [1]. The calculator gives it for a fluid of density 1,000 kilograms per cubic metre with the viscosity that you entered. A permeability of 1 darcy and a viscosity of 1 millipascal second give a K of about 9.7 × 10⁻⁶ metres per second.
Hydraulic resistance
The page also gives the hydraulic resistance, R = μ L ÷ (k A) [1]. It plays the role of an electrical resistance: the pressure drop is the resistance times the flow. Several layers in series add their resistances, and layers in parallel add their flows. This analogy is a convenient way to work out flow through layered soils.
When it applies
Darcy's law is valid only for slow, viscous flow [1]. A Reynolds number below one is clearly laminar, and flows up to a Reynolds number of 10 may still follow Darcy's law [1]. For faster flow, the page gives an inertial correction, the Forchheimer equation, which this calculator does not include [1]. In coarse gravel or near a well, check the Reynolds number.
Using the calculator
Select the units, choose the unit of the permeability, and enter the four values. Leave the viscosity blank for water. Read the flow in several units and the flux. To find how a change affects the flow, vary one value: the flow is directly proportional to the permeability, the area and the pressure drop, and inversely to the length and viscosity.
Soil and groundwater examples
Clean sand may have a permeability of the order of 10 darcies, silty sand about 0.1, and clay a few microdarcies, which are our own rough orders of magnitude. Through a sand layer of 10 darcies, 1 metre long and 1 square metre across, with a pressure drop of 10 kilopascals, the calculator gives about 0.1 litres per second, while the same pressure drop through clay gives only about a litre per year (for 3 microdarcies). This shows why clay layers hold back groundwater.
Flow in layers
For several layers of soil in series, where the flow passes through each in turn, the hydraulic resistances add, so the layer with the lowest permeability dominates. For layers side by side, where each carries its own flow, the flows add, and the layer with the highest permeability dominates. Use the calculator for each layer in turn, and combine the results in this way to find the flow through a layered ground.
Common mistakes
- Using the wrong permeability unit. Check darcy and m².
- Using the Darcy flux as the pore velocity. Divide by the porosity.
- Applying it to fast flow. It needs a low Reynolds number.
- Forgetting the viscosity. Oil flows more slowly than water.
What next
Use this often? Add Darcy's Law to your Home screen.
Frequently asked questions
What is a Darcy's law calculator?
A tool that finds the flow of a fluid through a porous medium.
What is Darcy's law?
Q = k A Δp ÷ (μ L).
What is the Darcy flux?
The flow rate divided by the area, Q ÷ A.
What is a darcy?
A unit of permeability, about 9.87 × 10⁻¹³ m².
When does Darcy's law hold?
For slow, viscous flow, with a Reynolds number below about 1 to 10.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.