A current divider calculator finds how a current splits between resistors that are connected in parallel. Enter the total current and the resistance of each branch, up to four, and it gives the current in each branch, the voltage across them and the total power.
How to use the current divider calculator
- Choose the unit of the current and enter the total current.
- Enter the resistance of each branch, at least two.
- Press Calculate.
The principle
In a current divider, the total current divides between parallel branches in inverse proportion to their impedances [1]. A branch with a low resistance carries more of the current, and one with a high resistance carries less. If the branches have the same value, the current is split equally [1]. The same voltage is across every branch, so each current is that voltage divided by its resistance.
The formula
The page gives the current in one branch as I_X = (R_T ÷ (R_X + R_T)) × I_T, where R_T is the resistance of the rest of the circuit in parallel with R_X [1]. For two resistors this becomes I_x = I_total × R_other ÷ (R_x + R_other), which is our own substitution, since the page has no separate two-resistor form. A 10 milliampere current through 1 kilohm and 2 kilohm gives 6.667 and 3.333 milliamperes.
The conductance form
The page also gives the form I_X = (Y_X ÷ Y_T) × I_T with admittances, and reminds readers that Y_T is a straightforward sum, not the sum of the inverses inverted [1]. For resistors, the admittance is the conductance G = 1 ÷ R. So each current is the total current times its conductance divided by the sum of all the conductances. The calculator uses this form, which works for any number of branches.
A worked example
A current of 10 milliamperes enters three branches of 1 kilohm, 2 kilohms and 3 kilohms. The conductances are 1, 0.5 and 0.333 millisiemens, adding to 1.8333. The currents are 5.4545, 2.7273 and 1.8182 milliamperes, which add up to the 10 milliamperes. The parallel resistance is 545.45 ohms, so the voltage across all three is 5.4545 volts. The numbers are our own.
Power
The power in each branch is the square of the voltage divided by its resistance, and the total power is the voltage times the total current, 54.545 milliwatts in the example. The branch with the smallest resistance carries the most current and dissipates the most power. The calculator shows the total power, so that you can check that the resistors are rated for it.
Loading
The page notes that when the source and the load are not ideal, current division reduces the gain of an amplifier: the input factor is R_S ÷ (R_S + R_in) and the output factor R_out ÷ (R_out + R_L) [1]. These are current dividers too. A load resistance that is much larger than the output resistance of the source loses little of the current, and one that is much smaller loses most of it.
Shunts
A common use of a current divider is the shunt of an ammeter. A small resistor in parallel with a sensitive meter carries most of the current, so that the meter reads a known fraction of the total. If the shunt is 1 ohm and the meter is 99 ohms, the meter gets 1 percent of the current, and the reading is multiplied by 100 to give the total.
Impedances
The page notes that the principle holds for impedances that depend on the frequency, such as a resistor in parallel with a capacitor [1]. The calculator handles resistors only. For an RC pair, the page gives the resistor's current as I_T ÷ (1 + jωCR), with the same time constant τ = CR [1]. Use the reactance calculator on this site for the impedance of the capacitor.
Using the calculator
Enter the total current in amperes or milliamperes and the resistance of at least two branches. Leave the last two blank for a two-branch divider. The results list each branch in order. To find a resistor that gives a given current, try values until the current matches, remembering that a smaller resistor takes a larger share.
Quick cases
Two equal resistors share the current equally, half each. If one resistor is ten times the other, for example 100 ohms and 1,000 ohms, the smaller one carries 10 × 1,000 ÷ 1,100, which is 90.9 percent of the current, and the larger one 9.1 percent. These two cases are worth remembering, and the calculator confirms them. They are our own examples.
Checking the result
Two checks catch most mistakes. First, the branch currents must add up to the total current that you entered. Second, the branch with the smallest resistance must carry the largest current. Also check that the voltage, which is the total current times the parallel resistance, is the same as the current in any one branch times its own resistance. The calculator shows the voltage so that you can do this.
Common mistakes
- Using it for resistors in series. Series resistors share voltage, not current.
- Entering a total current in the wrong unit. Check A or mA.
- Forgetting a branch. Include every parallel resistor.
- Using the wrong resistor in the formula. The other resistor goes in the numerator.
What next
Use this often? Add Current Divi to your Home screen.
Frequently asked questions
What is a current divider calculator?
A tool that finds how a current splits between parallel resistors.
What is the current divider rule?
I_x = I_T × R_other ÷ (R_x + R_other), or I_x = I_T × G_x ÷ G_total.
Which branch carries the most current?
The one with the lowest resistance.
How do I find the voltage across the branches?
Multiply the total current by the parallel resistance.
Does the rule work for impedances?
Yes, with admittances in place of conductances.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.