Saved

Press the star next to a tool's name to save it.

All my tools

Corrosion Rate Calculator

Use this corrosion rate calculator to find the average rate of metal loss in mm and mils per year from the mass lost, exposed area, exposure time and density.

Restored your last values ·

hours

Enter the mass the metal lost, the surface area that was exposed, the exposure time in hours and the density of the metal. You get the average corrosion rate in millimetres and mils per year. Add the thickness to see how long it would last at that rate.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the mass lost, the area, the time and the density, then press Calculate.

See full result

A corrosion rate calculator turns the weight a piece of metal lost into an average rate of corrosion, in millimetres and in mils per year. It is the calculator for a rust decay problem about real metal: enter the mass lost, the surface area, the time and the density of the metal. You can also enter the thickness to see how long it lasts at that rate.

How to use the corrosion rate calculator

  1. Choose US or metric units.
  2. Enter the mass lost, the exposed area and the exposure time in hours.
  3. Enter the density of the metal, such as 7.85 g/cm³ for steel.
  4. Add the thickness, if you want an estimate of the life, and press Calculate.

The weight-loss method

In the weight-loss method, a sample of metal is weighed, exposed to the environment for a time, cleaned and weighed again, which is our general description. The mass that it lost, divided by the area, the time and the density, gives the depth of metal lost per unit of time. A 2022 article on the exact calculation of corrosion rates by this method gives the formula as CR = k × m ÷ (A × t × ρ), where m is the mass loss, A the area, t the time and ρ the density [1].

The constant

In the article, the constant k is 8.76 × 10⁴ when the mass loss is in grams, the time in hours, the area in square centimetres and the density in grams per cubic centimetre, and the rate is then in millimetres per year [1]. The Alspi page gives the same constant in its table, and also 3.45 × 10⁶ for mils per year with the area in square centimetres [2]. We note, as our own working, that 8.76 × 10⁴ is 8,760 hours in a year times 10 millimetres in a centimetre.

A worked example

Take a steel coupon that lost 2.5 grams over 720 hours, which is 30 days, with an exposed area of 20 square centimetres and a density of 7.85 grams per cubic centimetre. The numerator is 87,600 × 2.5 = 219,000, and the denominator is 20 × 720 × 7.85 = 113,040. The rate is 1.9374 millimetres per year. None of the pages that we read gives a worked example, so this one is our own.

Mils per year

A mil is a thousandth of an inch, 0.0254 millimetres, and corrosion rates in the United States are often quoted in mils per year. We convert the rate in millimetres by dividing by 0.0254, so the example is 76.27 mils per year. The Alspi constant of 3.45 × 10⁶ gives 76.30, because that constant is rounded [2]. The small difference is only rounding, and either is a good estimate.

Metal lost over the test

The Alspi page also lists a constant of 10.0 for the metal loss in millimetres, with the area in square centimetres, and 393.7 for mils [2]. The loss is then 10 × m ÷ (A × ρ). For the example, it is 10 × 2.5 ÷ (20 × 7.85) = 0.15924 millimetres over the 720 hours, or 6.27 mils. This is the depth removed from the exposed surface, and the calculator shows it next to the yearly rate.

Estimating the life

If you enter the thickness, the calculator divides it by the yearly rate. A 3 millimetre plate corroding at 1.9374 millimetres per year would last about 1.5485 years. This is a straight-line extrapolation of our own and not a method from the pages. Real corrosion often slows down as a layer builds up or speeds up as it breaks away, so a short test is a poor guide to a long life.

US units

In US mode, the mass is in ounces, the area in square inches, the density in pounds per cubic inch and the thickness in inches. We change them into grams, square centimetres and grams per cubic centimetre before using the formula, with 1 ounce = 28.3495 grams, 1 square inch = 6.4516 square centimetres and 1 pound per cubic inch = 27.68 grams per cubic centimetre. These conversions are ours. Steel at 0.284 pounds per cubic inch is about 7.86 grams per cubic centimetre.

Densities to use

The density must be that of the metal that corroded. Steel is about 7.85 grams per cubic centimetre, which is the figure in our example, and aluminium is about 2.7. Use the value for your alloy from its data sheet. A wrong density changes the rate in proportion, so 10 percent error in the density gives about 10 percent error in the rate. The pages that we read do not give a table of densities.

What the method cannot show

The method gives an average over the whole surface. The Wikipedia article on corrosion gives the same relation, with the weight loss, the area and the density, as a general reference [3], but none of the pages deals with pitting, cracks or corrosion at a joint, where a small area is attacked quickly while the average loss is small. Nor do they describe how to clean the sample before weighing, which affects the result. Use a recognised test standard for any formal work.

Using the calculator

Weigh the sample before and after the test, and enter the mass lost, the exposed area, the time in hours and the density. Read the rate in millimetres and mils per year, and compare it with the maximum rate that is acceptable for your application. Repeat the test with several samples if you can. Note that this tool is about metal corrosion: it is not the damage timer of a computer game.

Common mistakes

  • Using the total area when only part was exposed. Use only the exposed surface.
  • Entering days instead of hours. The formula needs hours.
  • Using the wrong density. Use the density of the actual alloy.
  • Weighing without cleaning. Rust left on the sample hides the real loss.

What next

Use this often? Add Corrosion Ra to your Home screen.

Frequently asked questions

What is a corrosion rate calculator?

A tool that turns the weight a metal lost into an average corrosion rate in mm or mils per year.

What is the corrosion rate formula?

CR = 87,600 × m ÷ (A × t × ρ), with m in grams, A in cm², t in hours and ρ in g/cm³, giving mm per year.

What is a mil?

A thousandth of an inch, which is 0.0254 millimetres.

Is this a rust decay calculator for a game?

No. It is for metal corrosion, from the weight lost by a sample, not for the structure decay timer of a video game.

Does it show pitting?

No. The weight loss method gives an average, and pitting needs other tests.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools