Saved

Press the star next to a tool's name to save it.

All my tools

Compression Ratio to PSI Calculator

Use this compression ratio to psi calculator to estimate the pressure at the end of the compression stroke from the ratio, with gauge and absolute values.

Restored your last values ·

psi

Enter the engine's compression ratio. Leave the specific heat ratio blank to use 1.3 and the atmospheric pressure blank to use 14.696 psi.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter a value and press Calculate.

See full result

A compression ratio to PSI calculator estimates the pressure in a cylinder at the end of the compression stroke from the engine's compression ratio. Enter the ratio, and the calculator shows the pressure in psi, bar and kilopascals using a standard formula. It gives a handy figure to compare with a compression test, and it shows how the pressure rises as the ratio goes up.

What is the compression ratio?

Wikipedia defines the compression ratio as the ratio between the maximum and minimum volume during the compression stage of the power cycle. For the static ratio, it is the volume of the cylinder when the piston is at the bottom of its stroke divided by the volume when the piston is at the top. In a formula, CR = (Vd + Vc) ÷ Vc, where Vd is the displacement volume and Vc is the clearance volume. Petrol passenger car engines have typically had ratios between 8:1 and 12:1, and direct-injection diesel engines are often between 14:1 and 23:1.

The compression ratio to PSI formula

Cylinder pressure = atmospheric pressure × CR^γ
Gauge pressure = cylinder pressure − atmospheric pressure

The Wikipedia article gives this formula, where γ is a polytropic value for the ratio of specific heats for the gases at the temperatures present. Under ideal adiabatic conditions, the ratio of specific heats would be 1.4, but a lower value, generally between 1.2 and 1.3, is used. The calculator uses 1.3 unless you enter another value between 1.1 and 1.4. Because the formula gives absolute pressure, the calculator subtracts the atmospheric pressure to show the gauge pressure that a compression tester would read.

How to use the compression ratio to PSI calculator

  1. Enter the compression ratio, such as 9.5 for 9.5:1.
  2. Optionally enter the specific heat ratio. Leave it blank for 1.3.
  3. Optionally enter the atmospheric pressure. Leave it blank for 14.696 psi.
  4. Press Calculate to see the gauge and absolute pressure.

Worked examples

  • 7.5:1 with γ = 1.3: the ratio raised to the power 1.3 is 13.73, which is the figure Wikipedia uses in its example. At 14.7 psi atmospheric pressure the absolute pressure is about 202 psi, or about 187 psi gauge.
  • 9.5:1 with γ = 1.3: 9.5^1.3 is about 18.7, so the absolute pressure is about 274 psi and the gauge pressure about 260 psi.
  • 18:1 with γ = 1.3: 18^1.3 is about 42.8, so the absolute pressure is about 630 psi, or about 615 psi gauge. A diesel is in this range.

Static and dynamic compression ratio

The ratio on a spec sheet is the static ratio, which only uses the geometry of the cylinder. Wikipedia explains that the dynamic compression ratio is a more advanced calculation that also takes into account gases entering and leaving the cylinder during the compression phase. It is usually lower than the static ratio, but not always. If you know the dynamic ratio, enter it in the calculator for a closer estimate of the pressure. The inlet valve closing later, for example, shortens the real compression stroke and lowers the pressure.

Why a compression test differs

A compression test on a real engine is made while the engine is cranked slowly with the throttle open, so it measures a different state from the engine running. Leakage past the rings and valves, the cranking speed and the temperature of the walls all affect the number. Treat the formula as a theoretical guide and use the test for the health of the engine. If one cylinder reads much lower than the others, that points to a problem, whatever the formula says.

Why higher ratios raise pressure

A higher compression ratio squeezes the same amount of air into a smaller space, so the pressure and temperature rise. Wikipedia notes that a high compression ratio is desirable because it allows an engine to extract more mechanical energy from a given amount of fuel, due to its higher thermal efficiency. The price is a higher risk of knock in a petrol engine, so the fuel's octane rating and the engine design set a practical limit.

For pressure units see the pressure converter, for gauge and absolute pressure the psig to psia converter, and for gas relationships the ideal gas law calculator.

How the compression ratio to PSI calculator works

The calculator raises the compression ratio to the power of the specific heat ratio, multiplies it by the atmospheric pressure to get the absolute pressure at the end of compression, and subtracts the atmospheric pressure to show the gauge pressure. It also converts the result to bar and kilopascals, using 1 psi as about 6.894757 kilopascals.

Diesel and petrol engines

The same formula covers both kinds of engine, but the ratios differ. A petrol engine with a ratio of 10:1 gives a gauge pressure of about 279 psi with a ratio of specific heats of 1.3, while a diesel at 18:1 gives about 615 psi. Enter your ratio, and keep in mind that real engines may differ from the ideal.

Common mistakes

  • Comparing the result with a compression test. The two measure different things.
  • Using the ideal value of 1.4 for a real engine. Wikipedia says a lower value of 1.2 to 1.3 is used.
  • Forgetting atmospheric pressure. The formula gives absolute pressure.
  • Using the dynamic ratio as the static one. Enter the one you know and say which it is.

What next

Use this often? Add Compression to your Home screen.

Frequently asked questions

How does a compression ratio to psi calculator work?

It multiplies atmospheric pressure by the compression ratio raised to the power gamma, then subtracts atmospheric pressure to give the gauge pressure.

What is the formula for cylinder pressure?

Wikipedia gives cylinder pressure as atmospheric pressure times CR to the power γ, where γ is about 1.2 to 1.3 for real engines and 1.4 for ideal adiabatic compression.

What is a typical compression ratio?

Wikipedia says petrol passenger car engines have typically had ratios of 8:1 to 12:1, and direct-injection diesels are often 14:1 to 23:1.

Why does my compression test read lower than the calculator?

A real test is affected by leakage, cranking speed, valve timing and temperature, so it differs from the theoretical figure.

What is the difference between static and dynamic compression ratio?

The static ratio uses the cylinder geometry only. The dynamic ratio also accounts for gases entering and leaving during compression, and is usually lower.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools