Saved

Press the star next to a tool's name to save it.

All my tools

Coefficient of Discharge Calculator

Use this coefficient of discharge calculator to find the discharge coefficient of an orifice or a nozzle from a measured flow, or the actual flow from a known coefficient.

Restored your last values ·

Choose US or metric units and whether you know the flow or the coefficient. Enter the diameter of the opening, the pressure drop across it and the fluid density. You get the discharge coefficient or the actual flow, with the ideal flow.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the opening, the pressure drop and the other value, then press Calculate.

See full result

A coefficient of discharge calculator finds the discharge coefficient of an opening, such as an orifice or a nozzle, from a measured flow, or finds the actual flow from a known coefficient. Enter the diameter, the pressure drop and the fluid density. It also gives the ideal flow and the flow resistance.

How to use the coefficient of discharge calculator

  1. Choose US or metric units and what you want.
  2. Enter the diameter, the pressure drop and the measured flow or the coefficient.
  3. Press Calculate.

The definition

The discharge coefficient, also called the coefficient of discharge or the efflux coefficient, is the ratio of the actual discharge to the ideal discharge [1]. An ideal nozzle expands the same working fluid from the same starting conditions to the same exit pressure [1]. The coefficient is a number that describes how much less flow a real opening passes than the ideal one.

The formula

The page writes the coefficient as C_d = Q_actual ÷ Q_ideal, and for a mass flow, C_d = ṁ ÷ (A √(2 ρ Δp)) [1]. So the ideal volume flow through an opening of area A with a pressure drop Δp is Q = A √(2 Δp ÷ ρ), which is our own rearrangement of the mass-flow form. The calculator takes the area from the diameter of a round opening.

A worked example

For a round opening of 25 millimetres with a pressure drop of 50 kilopascals in water, the area is 0.00049087 square metres and the ideal flow is 4.9087 litres per second. If you measure a flow of 3 litres per second, the discharge coefficient is 0.611. This is typical for a sharp-edged orifice, a statement that is our own and is not on the page. The calculator reproduces these numbers.

Finding the flow

If you know the coefficient, the calculator finds the actual flow: Q = C_d A √(2 Δp ÷ ρ). With a coefficient of 0.6 in the same example, the flow is 2.9452 litres per second. This is useful for sizing an orifice, a valve or a hole, when you have a coefficient from a data sheet or a test.

Flow resistance

The page also gives the flow resistance k as 1 ÷ C_d² [1]. For a coefficient of 0.611 the resistance is 2.677, and for 0.6 it is 2.778. A lower coefficient means a higher resistance, so the same pressure drop gives less flow. The calculator shows this number in the working line for both modes.

Values above 1

For an orifice, the coefficient is usually below 1, because of the contraction of the jet and the friction. If you get a value above 1, the calculator warns you: it usually means that the flow, the diameter or the pressure drop was measured incorrectly, or that the units are wrong. In some other devices, such as a Venturi with a very smooth form, the values approach 1.

Units

In US mode the diameter is in inches, the pressure drop in psi and the flow in US gallons per minute. In metric mode, the diameter is in millimetres, the pressure drop in kilopascals and the flow in litres per second. The calculator converts to SI. Enter the density of the fluid in kilograms per cubic metre, or leave it blank for water at 1,000. These conversion factors are our own.

Where it is used

Discharge coefficients are used for orifice plates, nozzles, valves, weirs and the holes in tanks. Flow meters rely on them: the pressure drop across a known opening gives the flow, once the coefficient is known. Because the coefficient changes with the shape of the opening and the Reynolds number, it should be taken from a calibration or a standard for the device.

Limits

The calculator treats the opening as a simple circular hole in a thin plate, with the pressure drop measured across it. It does not account for the approach velocity, for gases that expand as they flow, or for a pipe that is not full. For liquids at moderate pressure drops, the results are a good first estimate.

Using the calculator

Pick the units and the mode. Enter the diameter and the pressure drop, then the measured flow to find the coefficient, or the coefficient to find the flow. Check the ideal flow in the result against the measured one, since the ratio of the two is the coefficient. Keep the units the same throughout.

Sizing an opening

To choose the diameter of an opening for a required flow, rearrange the equation: the area equals the flow divided by C_d √(2 Δp ÷ ρ). For 3 litres per second at 50 kilopascals of pressure drop in water with a coefficient of 0.6, the area is 0.0005 square metres, which is a diameter of about 25.2 millimetres. Check it in the calculator by entering 25 millimetres and the same pressure drop, which gives the flow of 2.945 litres per second at that coefficient.

Common mistakes

  • Using the pipe diameter instead of the opening. Use the opening.
  • Mixing gauge and differential pressure. Use the drop across the opening.
  • Expecting a value above 1. Check the measurements.
  • Using the coefficient for another opening. It depends on the shape.

What next

Use this often? Add Coefficient to your Home screen.

Frequently asked questions

What is a coefficient of discharge calculator?

A tool that finds the ratio of the actual flow through an opening to the ideal flow.

What is the coefficient of discharge?

C_d = actual discharge ÷ ideal discharge.

What is the ideal flow through an orifice?

Q = A √(2 Δp ÷ ρ).

What is the flow resistance?

k = 1 ÷ C_d².

What is a typical value for a sharp orifice?

Around 0.6, but it depends on the device.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools