A cement calculator tells you how much material to buy before you start pouring concrete. Enter the length, width and thickness of the job, pick a concrete grade, and this cement calculator shows how many 50 kg bags of cement you need, how much sand and coarse aggregate go with them, and what the cement will cost. It works with the standard nominal mixes used on many Indian sites, and you can also enter a custom ratio of your own.
How the cement calculator works
Freshly mixed concrete takes up less space than its dry ingredients do, because the fine particles and water fill the gaps. So the wet volume is first multiplied by a dry volume factor of 1.54. The dry total is then shared between cement, sand and aggregate according to the mix ratio.
- Wet volume = length × width × thickness
- Dry volume = wet volume × 1.54
- Cement volume = dry volume × cement parts ÷ total parts
- Bags of cement = cement volume × 1,440 ÷ 50
How to use the cement calculator
- Choose meters or feet.
- Enter the length, width and thickness. Convert thickness in inches or millimeters into the same unit first.
- Select the concrete grade, or choose Custom and enter your own parts.
- Add an allowance for waste if you want some extra.
- Enter the price per bag for a cost estimate, then press Calculate.
Concrete grades and mix ratios
In nominal mixes, a ratio such as 1:2:4 means one part cement, two parts sand and four parts coarse aggregate by volume. Common nominal mixes include:
- M5: 1:5:10, with a compressive strength of 5 MPa
- M10: 1:3:6, with a compressive strength of 10 MPa
- M15: 1:2:4, with a compressive strength of 15 MPa
- M20: 1:1.5:3, with a compressive strength of 20 MPa
Nominal mixes are covered by IS 456:2000. Stronger grades are normally produced as design mixes, in which an engineer sets the proportions after analyzing the actual materials.
Cement calculator example
Suppose you are pouring a floor 10 meters long, 4 meters wide and 0.15 meters thick, in M20 concrete. The wet volume is 6 cubic meters, and the dry volume is 6 × 1.54 = 9.24 cubic meters. The total of the ratio is 1 + 1.5 + 3 = 5.5, so cement is 9.24 ÷ 5.5 = 1.68 cubic meters. That is 1.68 × 1,440 ÷ 50 = 48.4 bags, so you would buy 49 bags. Sand comes to 2.52 cubic meters, and coarse aggregate to 5.04 cubic meters. At $8 a bag, the cement costs $392.
Why is the factor 1.54?
The factor of 1.54 is a widely used allowance, and it covers the shrinkage in volume that happens as the dry materials are combined with water. Some engineers use a slightly different value, depending on the materials and on local practice. Since a small change in the factor alters the total by only a little, the result is good enough for ordering materials. It is sensible to add a further allowance for waste, spillage and uneven ground.
Buying and storing cement
- Round up. Partly used bags are better than running short in the middle of a pour.
- Keep bags dry. Store them off the floor and covered, because moisture ruins cement.
- Use older bags first. Check the manufacture date when buying.
- Order sand and aggregate in the units your supplier uses. Many dealers in India sell by the cubic foot, which is why results are shown in cft too.
How to measure the job
For a slab, measure the length and the width of the area, and then decide on the thickness. Keep all three values in the same unit. If your drawing gives the thickness as 6 inches, enter 0.5 feet, and if it gives 150 millimeters, enter 0.15 meters. For an area with several sections, work out each part separately and add the bags together. A column or a beam can be calculated in just the same way, by treating its height or length, width and depth as the three sizes.
Cement, concrete and mortar
The words are often mixed up. Cement is the fine powder that binds everything together. Concrete is the finished mixture of cement, sand, coarse aggregate and water. Mortar, used between bricks and for plastering, contains cement and sand but no coarse aggregate, so it needs a different calculation from the one on this page.
Water and curing
This calculator doesn't estimate water, because the right amount depends on the grade, the moisture already in the sand, and how workable the mix needs to be. Adding too much water makes concrete easier to pour, but it weakens the finished slab. Once the concrete is placed, keep it damp during curing, so that it can reach its full strength. Your engineer or contractor can advise you about the right amount and how long to continue.
Common mistakes
- Forgetting the dry volume factor. Using wet volume alone leaves you short.
- Mixing units. A thickness in inches must be converted first.
- Using nominal mixes for structural work without advice. Ask a qualified engineer.
- Ignoring waste. Allow a little extra.
Related construction tools
Estimate volume with the concrete calculator, work out floors with the flooring calculator, and measure areas with the square footage calculator.
What next
Use this often? Add Cement to your Home screen.
Frequently asked questions
How does the cement calculator work?
It multiplies the wet volume by 1.54 to get dry volume, shares that by the mix ratio, and converts the cement volume into 50 kg bags.
How many bags of cement are needed for 1 cubic meter of M20?
About 8 bags of 50 kg, using a dry volume factor of 1.54 and a ratio of 1:1.5:3.
What does 1:2:4 mean?
One part cement, two parts sand and four parts coarse aggregate by volume.
Does it estimate water?
No. Water depends on the grade and on the moisture in your sand, so ask your engineer or contractor.
Can I use a custom mix?
Yes. Choose Custom ratio and enter your own cement, sand and aggregate parts.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.