Saved

Press the star next to a tool's name to save it.

All my tools

Carbon Equivalent Calculator

Use this carbon equivalent calculator to work out a steel's IIW and AWS carbon equivalent and Pcm from its composition, with a weldability rating and preheat guide.

Restored your last values ·

Enter the composition in weight percent from the mill certificate. Carbon and manganese are required; leave other elements blank for zero.

Everything is worked out in your browser. Nothing you type is sent anywhere.

Carbon equivalent (IIW)

–

Enter the steel's composition, then press Calculate.

See full result

This carbon equivalent calculator works out the carbon equivalent (CE) of a steel from its chemical composition, a quick way to judge how easy it is to weld. Enter the percentages of carbon, manganese and the other alloying elements from the mill certificate, and the carbon equivalent calculator gives the IIW and AWS carbon equivalents, the Pcm value, a weldability rating and a guide to preheat.

How to use the carbon equivalent calculator

  1. Find the composition on the steel's mill test certificate, in weight percent.
  2. Enter carbon and manganese, which are required.
  3. Enter the other elements if listed: silicon, chromium, molybdenum, vanadium, nickel, copper and boron. Leave blanks for zero.
  4. Press Calculate.

What is carbon equivalent?

The Wikipedia article on equivalent carbon content explains that carbon equivalent expresses the effect of the different alloying elements on a steel's hardenability as if they were extra carbon. Carbon has the biggest effect on how hard and brittle the heat-affected zone (HAZ) next to a weld can become as it cools, which raises the risk of cracking. The other elements matter too, but less, so each is divided by a factor before being added to the carbon content.

The IIW formula

The most widely used formula was developed by Dearden and O'Neill and adopted by the International Institute of Welding (IIW) in 1967:

CE = C + Mn/6 + (Cr + Mo + V)/5 + (Cu + Ni)/15

Wikipedia notes that it suits plain carbon and carbon-manganese steels, but not microalloyed high-strength low-alloy steels or low-alloy chromium-molybdenum steels.

The AWS formula and Pcm

The American Welding Society (AWS) formula, recommended for structural steels, adds silicon to the manganese term:

CE = C + (Mn + Si)/6 + (Cr + Mo + V)/5 + (Cu + Ni)/15

The AWS states that above a CE of 0.40% there's potential for cracking in the heat-affected zone at flame-cut edges and welds. For steels with low carbon, the Ito–Bessyo parameter, Pcm, adopted by the Japanese Welding Engineering Society, is also used: Pcm = C + Si/30 + (Mn + Cu + Cr)/20 + Ni/60 + Mo/15 + V/10 + 5B.

Weldability by IIW carbon equivalent

Carbon equivalentWeldability
Up to 0.35Excellent
0.36–0.40Very good
0.41–0.45Good
0.46–0.50Fair
Over 0.50Poor

Wikipedia adds that when the CE is between 0.40 and 0.60, preheating before welding may be necessary, and above 0.60 preheat is necessary and postheat may be too.

Worked example

Take a steel with 0.20% C, 1.20% Mn, 0.30% Si, 0.10% Cr, 0.05% Mo, 0.02% V, 0.10% Ni and 0.15% Cu. The IIW carbon equivalent is 0.20 + 1.20/6 + (0.10 + 0.05 + 0.02)/5 + (0.15 + 0.10)/15 = 0.20 + 0.20 + 0.034 + 0.017 = 0.451, rated good, with preheat possibly needed. The AWS value, which includes silicon, is 0.501, and Pcm is 0.290.

A plain carbon steel with 0.15% C and 0.60% Mn has a CE of 0.15 + 0.10 = 0.25, excellent weldability.

Reading the results

The big number is the IIW carbon equivalent, with its weldability rating below. The table shows the AWS carbon equivalent, the Pcm value and the preheat guidance from the IIW value.

Why some high-strength steels need care

Wikipedia notes that structural standards often limit individual alloying elements rather than CE, and that some high-strength steels now in use have a CE above 0.50% and have suffered brittle failures. Calculating CE from the actual mill certificate, rather than assuming typical values, helps catch steels that need preheat or special procedures.

Which elements matter most

The divisors in the formula show how strongly each element affects hardenability compared with carbon. Carbon counts in full. Manganese counts one-sixth as much, so 0.6% manganese adds the same as 0.1% carbon. Chromium, molybdenum and vanadium count one-fifth, and copper and nickel only one-fifteenth. That's why carbon content alone often decides whether a steel welds easily: in the plain carbon steel example, raising carbon from 0.15% to 0.25% lifts the CE from 0.25 to 0.35.

Where to find the composition

Steel is supplied with a mill test certificate, sometimes called a mill test report, which lists the chemical analysis of the heat it came from. Use those figures rather than the maximums in a material specification, since the actual values are usually lower and give a more accurate CE. If an element isn't listed, leave it blank; the calculator treats it as zero.

Using CE with other information

Carbon equivalent is one input to a welding plan, not the whole picture. Thicker plates cool faster after welding, hydrogen from moisture or consumables raises the risk of cracking, and restraint in the joint adds stress. Welding codes combine CE with thickness, hydrogen level and heat input to set preheat temperatures, so use the result as a guide and follow your procedure.

Rounding the result

The calculator shows the carbon equivalent to three decimal places and rates it after rounding to two, the way the weldability bands are written. A result of 0.451 rounds to 0.45 and is rated good, while 0.456 rounds to 0.46 and is rated fair.

Common mistakes

  • Using typical instead of actual values. Use the heat's certificate.
  • Mixing formulas. Compare IIW with IIW and AWS with AWS.
  • Ignoring thickness. Thicker sections cool faster and may need more preheat.
  • Using IIW for HSLA steels. The formula isn't meant for them.

Tips

  • Keep the mill certificate with the job file.
  • Check both IIW and AWS values for structural work.
  • Follow your welding procedure for preheat temperatures.

What next

Use this often? Add Carbon Equiv to your Home screen.

Frequently asked questions

How does a carbon equivalent calculator work?

It adds carbon to the other alloying elements divided by factors, using the IIW formula CE = C + Mn/6 + (Cr+Mo+V)/5 + (Cu+Ni)/15.

What is a good carbon equivalent for welding?

Up to 0.35 is excellent and 0.36–0.40 very good on the IIW scale; over 0.50 is poor.

When is preheat needed?

When CE is 0.40 to 0.60 preheat may be necessary; above 0.60 it is necessary.

What is the difference between the IIW and AWS formulas?

The AWS formula adds silicon to the manganese term and is recommended for structural steels.

What is Pcm?

The Ito–Bessyo parameter: C + Si/30 + (Mn+Cu+Cr)/20 + Ni/60 + Mo/15 + V/10 + 5B.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools