Saved

Press the star next to a tool's name to save it.

All my tools

Capacitor Size Calculator

Use this capacitor size calculator to find the capacitance that stores a given energy at a given voltage, or the energy or voltage from the other two values.

Restored your last values ·

µF
V

Choose the capacitor size to find the capacitance from an energy and a voltage. You can also find the energy from a capacitance and a voltage, or the voltage from a capacitance and an energy.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to find, enter the other two values, then press Calculate.

See full result

A capacitor size calculator finds the capacitance needed to store a given energy at a given voltage, using C = 2E ÷ V². Enter the energy and the voltage, and it gives the capacitance in microfarads, farads, nanofarads and picofarads. You can also solve for the energy or the voltage.

How to use the capacitor size calculator

  1. Choose what to find: the size, the energy or the voltage.
  2. Enter the other two values, and pick the energy unit.
  3. Press Calculate.

The energy formula

The energy stored in a capacitor is E = ½ C V², where C is the capacitance and V the voltage across it [1]. Turned round, the capacitance needed for a given energy is C = 2E ÷ V², which is our own rearrangement of that formula. The calculator uses this energy-based relation, for example to size a capacitor that must deliver a known amount of energy.

Charge and capacitance

The basic definition of capacitance is C = Q ÷ V, the charge divided by the voltage [1]. The calculator therefore shows the charge Q = C × V with every result. For a 1,487.6 microfarad capacitor at 110 volts, the charge is 0.16364 coulombs. This is our arithmetic from the definition, and it helps to check the other results.

A worked example for a motor

Suppose a start-up job needs 9 joules at 110 volts. Then C = 2 × 9 ÷ 110² = 18 ÷ 12,100 = 0.0014876 farads, which is 1,487.6 microfarads. This is our own arithmetic. Choose joules as the energy unit, enter 9 and 110, and the tool gives the capacitance in all four units.

A small example

Take 64 microjoules at 16 volts. Then C = 2 × 64 × 10⁻⁶ ÷ 256 = 0.5 microfarads, again our own arithmetic. Pick microjoules as the energy unit to enter 64 directly. The tool shows 0.5 microfarads, 500 nanofarads and 500,000 picofarads, so you can compare the value with the sizes on a parts list.

Finding the energy or the voltage

Choose the energy to find how much a capacitor stores at a voltage: E = ½ C V². Choose the voltage to find the voltage at which a given capacitor stores a given energy: V = √(2E ÷ C). For 1,487.6 microfarads and 9 joules, the voltage is 110 volts. Because the energy depends on the square of the voltage, a small change in voltage changes the energy a lot.

Motor capacitors

Motor start and run capacitors are chosen by the motor maker, not by an energy formula. The example above is a calculation of the energy-based value, not advice about a particular motor, so check what the manufacturer specifies. The tool gives only the energy-based value.

Choosing the voltage

The voltage you enter in the calculator is the voltage across the capacitor in the case you are studying. It is not the same thing as the rating of the part that you will buy. Capacitors carry a voltage rating, which for general electronics runs from a few volts to about 1 kilovolt [1], and the part must be rated at least for the voltage it will see. A margin above that is our own advice.

Warnings

A capacitor larger than recommended for a motor can raise the current drawn and overheat the windings. This is general engineering caution and not a figure from our source. The calculation does not account for temperature rating or for the tolerance of the part. We repeat both warnings here: this is a first estimate of the size, and the specification of the manufacturer always comes first.

What it does not do

The tool does not give the cut-off of a filter or power-factor correction. It does not choose a part, and it uses no constants beyond the formulas above. If you need a filter capacitor, use a filter calculator. For series and parallel combinations, charge and the time constant, use a dedicated capacitor combination tool.

Using the calculator

Pick the quantity you need, enter the other two, and check the units, especially joules against millijoules and microjoules. Compare the result in microfarads with the standard values that suppliers list, and round up to the next preferred value only after checking the voltage rating and tolerance.

Energy units

The energies in the two examples are very different. The start-up example above is 9 joules, while the small example is 64 microjoules. The energy unit selector multiplies the number you type by 1, 0.001 or 0.000001 before the calculation. The capacitance is shown in four units so that you can match a datasheet: one microfarad is 1,000 nanofarads, and one nanofarad is 1,000 picofarads.

How voltage changes the size

Because the voltage is squared in the formula, it has a strong effect on the capacitance. For the same 9 joules, doubling the voltage from 110 to 220 volts cuts the size to a quarter, from 1,487.6 to about 371.9 microfarads. This is our own arithmetic from C = 2E ÷ V². It is the reason why the voltage you enter should be the real voltage across the capacitor in your case.

Common mistakes

  • Mixing joules and millijoules. Choose the right energy unit.
  • Forgetting that voltage is squared. A small voltage change gives a large change in size.
  • Taking the result as a part number. Check the specification.
  • Ignoring the voltage rating. The part must be rated for the operating voltage.

What next

Use this often? Add Capacitor Si to your Home screen.

Frequently asked questions

What is a capacitor size calculator?

A tool that finds the capacitance needed to store a given energy at a given voltage, using C = 2E ÷ V².

What is the formula for the size of a capacitor?

C = 2E ÷ V², from the stored energy E = ½ C V².

How big a capacitor stores 9 J at 110 V?

About 1,487.6 µF, which is 0.0014876 F.

Does the tool pick a motor capacitor?

No. It gives the energy-based value only, and the manufacturer's specification, the tolerance and the voltage rating come first.

Can it find the voltage or the energy?

Yes. Choose the energy or the voltage as the quantity to find and enter the other two values.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools