Saved

Press the star next to a tool's name to save it.

All my tools

Cable Impedance Calculator

Use this cable impedance calculator to find the characteristic impedance of a coaxial cable or a PCB microstrip from its size and insulation, or from inductance and capacitance.

Restored your last values ·

For coaxial cable, enter the inside diameter of the shield, the diameter of the inner conductor and the permittivity of the insulation. For a microstrip, enter the trace width, its height above the ground plane and the permittivity of the board. You can also enter the inductance and capacitance per metre of any line.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose the cable type, enter the sizes and the insulation, then press Calculate.

See full result

A cable impedance calculator finds the characteristic impedance of a transmission line from its dimensions and materials. Enter the diameters and the insulation of a coaxial cable, or the width, height and board material of a microstrip trace, or the inductance and capacitance per metre of a line, and you get the impedance in ohms and the speed of the signal. It is useful for RF work, antenna cables, video and circuit board design. It runs in your browser.

How to use the cable impedance calculator

  1. Choose coaxial cable, microstrip or inductance and capacitance.
  2. Enter the sizes and the permittivity, or the inductance and capacitance.
  3. Press Calculate.

What characteristic impedance is

The Wikipedia article on characteristic impedance says that for a lossless line, in which the resistance and the conductance are both zero, the impedance reduces to Z₀ = √(L ÷ C), where L is the inductance and C the capacitance per unit length. It says that the impedance is then wholly real, and that it no longer depends on the frequency.[3] The calculator's third mode uses this directly. For 250 nH/m and 100 pF/m, Z₀ = √(250 × 10⁻⁹ ÷ 100 × 10⁻¹²) = √2,500 = 50 ohms.

Coaxial cable

The article on coaxial cable gives the capacitance and the inductance per metre of a coax with the shield inside diameter D and the inner conductor outside diameter d: C = 2πε ÷ ln(D ÷ d) and L = (μ ÷ 2π) ln(D ÷ d).[1] Putting them into Z₀ = √(L ÷ C) gives Z₀ = (1 ÷ 2π)√(μ ÷ ε) ln(D ÷ d). With the permeability of free space and the permittivity εr of the insulation, that is about 59.96 ÷ √εr times the natural logarithm of D ÷ d, or 138 ÷ √εr times the base-10 logarithm. This is derived from the page's formulas, and the calculator uses it. For polyethylene, with εr = 2.25, and D ÷ d = 3.5, the impedance is 50.07 ohms.

Typical impedances

The article on characteristic impedance says that the impedance of coaxial cables is commonly chosen to be 50 ohms for radio-frequency and microwave applications, and that coax for video is usually 75 ohms for its lower loss.[3] The coax page says that the choice of 50 ohms is a compromise between the capability to carry power and the attenuation. To reach 75 ohms with the same polyethylene insulation, the ratio D ÷ d must be about 5.6. The calculator shows the inductance and the capacitance per metre as well, which are typically 250 nH/m and 100 pF/m for a 50 ohm cable.

Microstrip

A microstrip is a flat trace on one side of a circuit board, with a ground plane on the other. The article on microstrips gives Hammerstad's equations, which modify Wheeler's, for the impedance. For a width-to-height ratio w ÷ h of 1 or less, Z = (Z₀ ÷ (2π√εeff)) ln(8h ÷ w + w ÷ 4h). For a ratio of 1 or more, Z = Z₀ ÷ (√εeff [w ÷ h + 1.393 + 0.667 ln(w ÷ h + 1.444)]). Here Z₀ is the impedance of free space, about 376.73 ohms, and the effective permittivity is εeff = (εr + 1) ÷ 2 + ((εr − 1) ÷ 2) q, with q a function of the ratio.[2] For a board with εr = 4.4, a height of 1.6 mm and a trace of 3 mm, which has a ratio of 1.875, the impedance is about 50.8 ohms. A narrow trace of 0.8 mm gives about 95 ohms.

The speed of the signal

The velocity factor is the speed of the signal as a share of the speed of light. For a coax with a uniform insulation it is 1 ÷ √εr, so polyethylene gives 0.667, about two thirds. For a microstrip the factor is 1 ÷ √εeff. This matters in antenna cables and in delay lines, where the length of the cable sets a time or a phase. The calculator shows it in all three modes. In the inductance and capacitance mode, it is 1 ÷ √(LC) divided by the speed of light.

Matching and why it matters

A cable carries a signal without reflections only when it is connected to a load that has the same impedance as the cable. A mismatch sends part of the signal back. This is why radio equipment and cables are made for 50 ohms, and video for 75 ohms. On a circuit board, a trace that carries a fast signal is designed with a width that gives the impedance of the driver, often 50 ohms. If you know the board thickness and material, you can find the width that you need by trying values in the microstrip mode until the impedance is right.

Designing a cable or a trace

If you want a certain impedance, work backwards from the formula. For a coax with polyethylene insulation, a ratio D ÷ d of about 3.5 gives 50 ohms. Enter your insulation and try a few diameters until the result matches, then check the cable data sheet. For a microstrip, a thinner board needs a narrower trace for the same impedance, and a board with a higher permittivity needs a narrower trace too. The calculator makes these trials quick, since it recalculates as soon as you press the button. Pair it with a voltage drop or a frequency calculator for the rest of the design.

Common mistakes

  • Mixing up D and d. D is the larger size, the shield, and d is the inner conductor.
  • Using the thickness of the cable jacket. Use the inside of the shield.
  • Using the permittivity of air for a solid insulation. Use the value for the insulation.
  • Forgetting the frequency limits. The results are for a lossless line.

What next

Use this often? Add Cable Impeda to your Home screen.

Frequently asked questions

What is a cable impedance calculator?

A tool that finds the characteristic impedance of a transmission line, such as a coaxial cable or a circuit board trace, from its dimensions and materials.

What is the formula for coax impedance?

Z₀ = (59.96 ÷ √εr) ln(D ÷ d), or 138 ÷ √εr times log₁₀(D ÷ d). It follows from Z₀ = √(L ÷ C).

What impedance should coax have?

50 ohms is common for RF and microwave use, and 75 ohms for video, for its lower loss.

How do I find the impedance from L and C?

For a lossless line, Z₀ = √(L ÷ C). With 250 nH/m and 100 pF/m, it is 50 ohms.

What is the velocity factor?

The speed of the signal as a share of the speed of light, 1 ÷ √εr for coax. For polyethylene it is about 0.67.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools