Saved

Press the star next to a tool's name to save it.

All my tools

Bridge Rectifier Calculator

Use this bridge rectifier calculator to find the peak and average DC output of a full-wave bridge from the AC voltage, and the ripple with a smoothing capacitor.

Restored your last values ·

Enter the RMS voltage of the AC supply to the bridge. The calculator gives the peak and average output after the diodes. Add the load current, the capacitor and the frequency to estimate the ripple and the smoothed DC voltage.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the AC voltage, then press Calculate.

See full result

A bridge rectifier calculator finds the DC output of a full-wave bridge rectifier from the AC voltage that feeds it. It gives the peak and average output after the diode drops. With the load current, a smoothing capacitor and the frequency, it estimates the ripple and the smoothed DC voltage.

How to use the bridge rectifier calculator

  1. Enter the AC voltage in volts RMS.
  2. Add the diode drop if it is not 0.7 volts.
  3. Add the load current, capacitor and frequency for the ripple.
  4. Press Calculate.

How a bridge works

A diode bridge turns an AC voltage into a polarized, pulsating voltage of the same amplitude but twice the frequency [1]. Only two of the four diodes conduct at any time, one pair on each half cycle [1]. The result can be considered as a DC voltage with a very large ripple on it [1]. A capacitor is added to smooth the ripple.

The ideal values

The page on rectifiers gives the average and RMS output of an ideal single-phase full-wave rectifier: V_dc = 2 V_peak ÷ π and V_rms = V_peak ÷ √2 [2]. For an AC supply of 12 volts RMS, the peak is √2 × 12 = 16.97 volts, and the ideal average output is 10.80 volts. These values assume diodes with no voltage drop and no capacitor.

The diode drops

In a bridge, the current passes through two diodes at a time, so two diode drops are lost. A silicon diode drops about 0.7 volts, a figure that is our own and that the calculator uses unless you enter another. The peak output is then 16.97 − 1.4 = 15.57 volts, and the average is 2 × 15.57 ÷ π = 9.91 volts. Schottky diodes with a lower drop give more output at low voltages.

The ripple

With a smoothing capacitor C, the ripple voltage for a load current I and a ripple frequency of 2f is about ΔV = I ÷ (2 f C). This is a common approximation, and it is our own working, as the pages that we read give no ripple formula. For 1 ampere, 2,200 microfarads and a 50 hertz supply, the ripple is 4.5455 volts peak to peak, and the DC output is about 13.30 volts.

Choosing the capacitor

A bigger capacitor gives a smaller ripple, but a larger surge when the supply is switched on and a higher peak current in the diodes. If the ripple is as large as the peak voltage, as in a small capacitor with a large load, the calculator says that the capacitor is too small. Try several values to see how the ripple falls in proportion to the capacitance.

Ratings of the diodes

Each diode must stand the peak voltage in the reverse direction. In a bridge, that is about the peak of the secondary voltage, 16.97 volts in the example, though in practice a margin of at least two times is used. The current rating must cover the load current, and the peaks of current that charge the capacitor. The calculator shows the peak voltage that each diode must withstand.

Frequency

The ripple frequency is twice the frequency of the supply: 100 hertz for a 50 hertz supply, 120 hertz for a 60 hertz one. The page notes that a full-wave rectifier gives far less ripple than a half-wave one [2]. Enter 50 or 60 for the mains frequency. A higher supply frequency allows a smaller capacitor for the same ripple.

Limits

The calculator gives estimates for a single-phase bridge that feeds a resistive or steady load. The real output also falls with the resistance of the transformer and the diodes, and with the load current. The formulas are for an ideal AC source. For power supplies that need to be exact, measure the circuit or use a simulation.

Using the calculator

Enter the RMS voltage of the secondary. Leave the diode drop blank for silicon diodes, or enter your own. Add the current, the capacitor and the frequency to see the ripple. Compare the result with the voltage that your circuit needs, and add a regulator after the capacitor if you need a steady supply.

A worked example with numbers

Take a transformer with 12 volts RMS on the secondary, silicon diodes, a load of 1 ampere and a capacitor of 2,200 microfarads on a 50 hertz supply. The peak voltage before the diodes is 16.97 volts. After the two diode drops it is 15.57 volts. The ripple is 4.55 volts peak to peak, so the voltage swings between 15.57 and 11.03 volts, with an average of about 13.30 volts. Doubling the capacitor halves the ripple to 2.27 volts. These are our own calculations from the formulas above.

Half-wave comparison

A half-wave rectifier has only one diode and uses only half of each cycle, so its ripple frequency is the same as the supply, and its ripple is about twice as large for the same capacitor. This is why a bridge is preferred for power supplies, despite needing four diodes.

Common mistakes

  • Using the peak voltage as the RMS value. The RMS is 0.707 of the peak.
  • Forgetting the two diode drops. A bridge loses two.
  • Using too small a capacitor. The ripple will be large.
  • Choosing diodes with no margin. Allow twice the peak voltage.

What next

Use this often? Add Bridge Recti to your Home screen.

Frequently asked questions

What is a bridge rectifier calculator?

A tool that finds the DC output of a full-wave bridge from the AC input.

What is the average output of a full-wave rectifier?

V_dc = 2 V_peak ÷ π for an ideal rectifier.

How many diode drops are lost in a bridge?

Two, since two diodes conduct at a time.

How do I estimate the ripple with a capacitor?

ΔV ≈ I ÷ (2 f C).

What is the ripple frequency?

Twice the supply frequency.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools