A belt length calculator finds the length of a belt that runs round two pulleys, from their diameters and the distance between their centres. It works for an open belt, where both pulleys turn the same way, and a crossed belt, where they turn opposite ways, and it gives the wrap angles.
How to use the belt length calculator
- Choose US or metric units and the belt type.
- Enter the two diameters and the centre distance.
- Press Calculate.
The belt problem
The length of a belt round two circles is a classical problem. The page on the belt problem gives the answers for both kinds of belt [1]. The length depends on the radii of the pulleys, r₁ and r₂, and the distance P between their centres. The calculator takes the diameters, halves them and applies the formulas.
Open belt
For an open belt, the length is L = 2P sin(θ ÷ 2) + r₁ (2π − θ) + r₂ θ, where θ = 2 arccos((r₁ − r₂) ÷ P) and r₁ is the larger radius [1]. The belt wraps the larger pulley by 2π − θ and the smaller by θ. For pulleys of 200 and 100 millimetres, 500 millimetres apart, the belt is 1,476.24 millimetres long, with wraps of 191.48 and 168.52 degrees.
Crossed belt
For a crossed belt, the page gives L = 2 (r₁ + r₂)(tan φ + π − φ), with cos φ = (r₁ + r₂) ÷ P [1]. For the same pulleys at 500 millimetres, the belt is 1,516.59 millimetres long. Each pulley is wrapped by the same angle, 2π − 2φ, which is 214.9 degrees in this example. A crossed belt is longer and has a better grip, but it rubs against itself where it crosses.
A feature of the crossed belt
The page notes that, for a fixed distance between the centres, the length of a crossed belt depends only on the sum of the radii [1]. So pulleys of 150 and 150 millimetres give the same crossed belt as pulleys of 200 and 100 millimetres at the same spacing. You can check this in the calculator by changing the two diameters and keeping their sum constant.
US units
Enter the diameters and the distance in inches, and the belt length is given in inches and in feet. Pulleys of 8 and 4 inches, 20 inches apart, need an open belt of 59.05 inches, which is 4.92 feet. The calculator works in the units that you choose and does not convert between systems, which keeps the result simple to check.
Centre distance
For V-belts, the page says that the preferred centre distance is larger than the largest pulley diameter, but less than three times the sum of both pulley diameters [2]. A centre distance in this range gives a good wrap angle and a belt of moderate length. The calculator does not enforce the limit, but you can test a design against it.
Wrap angle
The wrap angle is how much of each pulley the belt touches. A small wrap angle on the smaller pulley limits the power that can be carried, since the belt grips less. The page relates the belt tensions by T₁ ÷ T₂ = e^(μα), where μ is the friction and α the contact angle [2]. Open belts with very different pulleys give a small angle on the smaller one.
Limits
The result is the length of the belt along the centre of its thickness or at the pitch line, if you enter the pitch diameters. For a V-belt or a timing belt, use the pitch diameters, and select the nearest standard length. The calculation also leaves out sag, stretch and the take-up that the drive needs, so allow some adjustment in the centre distance.
Using the calculator
Select the belt type, enter the diameters and the centre distance and press the button. Check that the centre distance is greater than the larger radius minus the smaller for an open belt, and greater than the sum of the radii for a crossed belt, or the calculator reports an overlap. Compare the open and crossed lengths for the same drive.
Equal pulleys
When the two pulleys are the same size, the open belt is the simplest case: two straight runs of the centre distance and a half turn round each pulley. With two 150 millimetre pulleys 500 millimetres apart, the belt is 2 × 500 plus the circumference of one pulley, 471.24, which is 1,471.24 millimetres. An open belt then wraps each pulley by exactly 180 degrees, which is the largest wrap that it can have.
Same sum, same crossed belt
Two pulleys of 150 millimetres at 500 millimetres, crossed, give a belt of 1,516.59 millimetres, the same as the 200 and 100 millimetre pair. This follows from the property of the crossed belt quoted above, and it is a good check on the calculator: change the diameters while keeping their sum, and watch the result stay the same.
Choosing between open and crossed
Use an open belt when both pulleys should turn the same way, which is the usual case. Use a crossed belt only when the driven pulley must turn the opposite way, and when the drive can tolerate the extra wear. A crossed belt needs a longer belt, and the pulleys should be well apart so that the twist is gentle, since the belt rubs against itself at the crossing point.
Common mistakes
- Using the radius as the diameter. Enter diameters.
- Using the outside diameter for V-belts. Use the pitch diameter.
- Choosing the wrong belt type. Crossed belts reverse rotation.
- Setting the centre distance too small. The pulleys must not overlap.
What next
Use this often? Add Belt Length to your Home screen.
Frequently asked questions
What is a belt length calculator?
A tool that finds the length of a belt round two pulleys.
What is the formula for an open belt?
L = 2P sin(θ ÷ 2) + r₁ (2π − θ) + r₂ θ, with θ = 2 arccos((r₁ − r₂) ÷ P).
What is the formula for a crossed belt?
L = 2 (r₁ + r₂)(tan φ + π − φ), with cos φ = (r₁ + r₂) ÷ P.
Does a crossed belt depend on the pulley sizes?
Only on their sum, for a fixed centre distance.
What is the wrap angle?
The angle of each pulley that the belt touches.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.