A wing loading calculator divides the weight of an aircraft by the area of its wings. It also gives the wing cube loading, which divides the weight by the wing area to the power of 1.5. Enter the weight and the wing area, and compare the result with gliders, light aircraft and jets.
How to use the wing loading calculator
- Choose US or metric units.
- Enter the weight and the wing area.
- Press Calculate.
What wing loading is
Wikipedia defines wing loading as the total weight of an aircraft or flying animal divided by the area of its wing [1]. It is expressed in mass per area, in pounds per square foot or kilograms per square metre, and not as a force per area [1]. As a formula, WL = W ÷ S, where W is the weight and S the wing area.
Which weight to use
Wing loading is usually quoted for the gross weight or the maximum take-off weight, and Wikipedia's table lists mostly maximum take-off figures [1]. A loaded aircraft has a higher wing loading than an empty one, so the figure depends on what you load. Pilots and designers therefore often quote it for the maximum take-off weight, and sometimes also for a typical flying weight.
Wing cube loading
The tool also gives the wing cube loading, WCL = W ÷ S^1.5. This is our own addition and is not on the Wikipedia page we cite. Because the area is raised to the power of 1.5, the value is a weight per unit volume, with units like kilograms per cubic metre. It is used to compare aircraft of different sizes, since it takes some account of the fact that a larger aircraft has a larger wing area but also a greater weight.
A worked example
Take an aircraft with a wing area of 23 square metres and a weight of 10,400 kilograms. The wing loading is 10,400 ÷ 23 = 452.2 kilograms per square metre, and the wing cube loading is 10,400 ÷ 23^1.5 = about 94.3 kilograms per cubic metre. Enter 10,400 and 23 in metric mode to see the same results from the calculator.
Typical values
Wikipedia lists the Schleicher ASW 22 glider at 50.9 kilograms per square metre (10.4 pounds per square foot) and gives the UK Civil Aviation Authority limit for a microlight as 25 kilograms per square metre [1]. The tool's comparison line also uses its own broad bands: radio-controlled hobby models between 0.625 and 2.5 pounds per square foot, gliders below about 100 kilograms per square metre, and fighters near 377 kilograms per square metre. Those bands are the tool's own planning figures. The calculator tells you where your value lies.
Airliners
Wikipedia's table, as we read it from a summary, lists much higher values for large airliners than for light aircraft, in the hundreds of kilograms per square metre. We do not quote the figures here, because we could not read them verbatim, and the tool has no airliner band.
Speed and turning
Wikipedia says that a lower wing loading means a lower stalling speed, so an aircraft can take off and land more slowly, and that take-off speed is proportional to the square root of the wing loading [1]. It also says that the lower the wing loading, the tighter the turn [1]. These are simplified statements without constants.
Units and conversions
In US mode the weight is in pounds and the area in square feet, so the result is in pounds per square foot. In metric mode, it is in kilograms and square metres. The calculator also gives the value in the other unit system, using 1 pound per square foot = 4.8824 kilograms per square metre, which comes from the definitions of the pound and the foot and is our own working. The wing cube loading is given in the unit of the system that you chose.
What it leaves out
The aspect ratio and the configuration of the wing also matter, but the calculator does not work out stall speeds, turn radii or load factors. It also takes the wing area as given, so you must measure the planform area of the wings, including the part that passes through the fuselage, in the way that the maker defines it. Wikipedia notes that the wing area includes the ailerons [1].
Using the calculator
Pick the units, enter the weight and the wing area, and press the button. Try the same aircraft at an empty and a loaded weight to see how the loading changes. Compare two designs with the wing cube loading when one is much larger than the other. The comparison line tells you whether your value is glider-like, in between, or near a fighter, using the tool's own bands.
A US units example
Take our own example of a light aircraft with a gross weight of 2,400 pounds and a wing area of 160 square feet. The wing loading is 2,400 ÷ 160 = 15 pounds per square foot [1]. In metric units that is 15 × 4.8824 = 73.2 kilograms per square metre.
That is more than the 50.9 kilograms per square metre listed for the Schleicher ASW 22 glider [1], so this aircraft would have a higher stalling speed than the glider. Now imagine a lighter day with 2,000 pounds on board. The loading falls to 12.5 pounds per square foot, a drop of about 17 percent. Enter both weights in the calculator to see the change.
Common mistakes
- Using the empty weight when comparing with published values. Use the maximum take-off weight.
- Mixing pounds with square metres. Stay in one unit system.
- Treating wing loading as a force per area. It is a mass per area.
- Forgetting that wing area is the planform area. Measure it from above.
What next
Use this often? Add Wing Loading to your Home screen.
Frequently asked questions
What is a wing loading calculator?
A tool that divides the weight of an aircraft by its wing area and also gives the wing cube loading.
What is the wing loading formula?
Wing loading is the weight divided by the wing area, WL = W ÷ S.
What is wing cube loading?
The weight divided by the wing area to the power of 1.5.
What wing loading does a glider have?
The tool treats under about 100 kilograms per square metre as glider-like. Wikipedia lists the ASW 22 glider at 50.9.
Does a lower wing loading mean a lower stall speed?
Yes, Wikipedia calls wing loading a useful measure of the stalling speed.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.