A winch size calculator estimates the pull needed to drag a load up a slope and the rating of the winch to buy. It uses the line pull formula of a marine supplier and the typical safety factor of 2 to 1. Enter the weight, the slope and the surface, and you get a range of line pull and a winch rating.
How to use the winch size calculator
- Choose US or metric units.
- Enter the weight of the load and the slope as a percent grade.
- Choose what the load moves on, or type your own friction coefficient.
- Press Calculate.
The line pull formula
A marine equipment guide gives the line pull needed as the weight of the load multiplied by the sum of the grade resistance and the coefficient of friction, W × (Gr + Cf) [1]. The grade resistance Gr comes from the slope, and the coefficient Cf comes from the surface. On level ground there is no slope, so the line pull is only the weight times the friction. The calculator applies this formula as the guide states it.
The grade resistance table
The guide lists the grade resistance for each slope, for example 0.288 at a 30 percent grade, 0.448 at 50 percent and 0.701 at 100 percent [1]. The calculator holds the guide's table, from 5 percent up to 400 percent, and reads values between rows in a straight line. That interpolation, and the zero at a level slope, are our own working. A slope above 400 percent is out of range, and the guide treats a vertical lift as 1.
The friction coefficients
The guide gives ranges for the coefficient: a load on wheels 0.02 to 0.05, on rollers 0.05 to 0.10, steel on concrete 0.30 to 0.70, steel on steel 0.40 to 0.60, and wood on concrete 0.40 to 0.60 [1]. Pick the surface and the page shows the pull for the low and the high end. If you know the real coefficient, type it in and the page uses that single value in place of the range.
A worked example
The guide's example is a load of 5 tons on a 30 percent slope, on wheels. The line pull is 5 × (0.288 + 0.02) to 5 × (0.288 + 0.05), or 1.54 to 1.69 tons [1]. In pounds, enter 10,000 and the calculator returns 3,080 to 3,380 pounds, the same numbers in smaller units. The tons are short tons of 2,000 pounds, a conversion that we made ourselves.
The 2 to 1 safety factor
The guide says that typical safety factors are about 2 to 1 for a winch [1]. So the calculator doubles the line pull to give a rating: for the example, 6,160 to 6,760 pounds. The factor covers things that the formula leaves out, such as shock loads and wear. A heavier or riskier job calls for a larger margin, which is our own advice, so choose a winch above the figure shown.
What the formula does not include
The guide's formula covers only the weight, the slope and the surface. Rope and pulley friction and other inefficiencies are not included here, and the guide says the same of its multi-part line figures [1]. Winches also lose pull as rope builds up on the drum, and a snatch block changes the line pull, which are our own notes. The estimate is for the pull along the slope, from the weight and the surface only, which makes it a starting point, and not the last word.
Why we did not use the other method
This tool follows one marine supplier's guide, which has a worked example and a stated safety factor [1]. It does not cover vehicle recovery from mud or sand, which depends on factors that the guide does not give.
Metric units
Choose metric to enter the weight in kilograms. The line pull is then shown in kilograms of force and in kilonewtons, at 9.80665 newtons to the kilogram of force, our own conversion. The coefficients and the grade table are pure numbers, so they do not change. The result for 4,500 kilograms on a 35 percent grade, on steel on concrete, is 2,835 to 4,635 kilograms of force before the safety factor.
Using the result safely
Treat the winch rating as a minimum. Check the maker's rated line pull on the first layer of rope and on the layer you will use, and check the strength of the rope, hooks and anchors, because the weakest part sets the limit. Have a qualified person check the rigging, and stay clear of the line. This page is educational, and cannot replace a rigging plan.
Choosing the surface
The surface sets the friction, and the range is wide for hard surfaces. A load on wheels or rollers needs little force on the level, so the slope dominates the result. A steel or wooden load dragged over concrete, in contrast, can need more pull for friction than for the slope. If you are unsure, read the high end of the range, and pick a winch for that figure. Wet, muddy or dusty surfaces can change the coefficient, and the guide does not cover them, so measure the real pull with a scale where you can.
Common mistakes
- Using the vehicle weight and ignoring the slope. A slope adds to the pull.
- Taking only the low friction end. Use the high end to be safe.
- Choosing a winch exactly at the line pull. Use the 2 to 1 factor.
- Forgetting the rope and anchors. The weakest part sets the limit.
What next
Use this often? Add Winch Size to your Home screen.
Frequently asked questions
What is a winch size calculator?
A tool that estimates the line pull needed to move a load on a slope and the winch rating to buy.
How is the line pull calculated?
Line pull = weight × (grade resistance + coefficient of friction).
What safety factor should a winch have?
The guide says typical safety factors are about 2 to 1 for a winch.
Does it include rope friction?
No. Rope and pulley friction and other inefficiencies are not included.
Is it safe to rely on this winch size calculator?
It is an estimate only. Check the maker's rating and have a qualified person check the rigging.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.