A Wheatstone bridge calculator finds an unknown resistance from three known resistors when the bridge is balanced, and also finds the output voltage of an unbalanced bridge from the supply voltage. It is the classic circuit for measuring resistance, and it is used in strain gauges and sensors.
How to use the wheatstone bridge calculator
- Choose unknown resistance or output voltage.
- Enter the resistors R₁, R₂ and R₃ in ohms.
- For the voltage, add the supply voltage and the unknown resistor.
- Press Calculate.
What a Wheatstone bridge is
A Wheatstone bridge is a circuit of four resistors in two voltage dividers, with a meter, the galvanometer, connected between the two midpoints. In the circuit on the Wikipedia page, R₁ and R₃ are known, R₂ is adjustable, and Rₓ is the unknown resistance to be measured [1]. You adjust R₂ until the meter reads zero, which is the balance point. The page reads the unknown resistor from the setting.
The balance condition
When the measured voltage across the meter is zero, the bridge is balanced and R₂ ÷ R₁ = Rₓ ÷ R₃, so Rₓ = R₃ × R₂ ÷ R₁ [1]. No current flows through the galvanometer at balance, so the result does not depend on the supply voltage or on the meter. That is why the bridge is accurate: it only compares ratios of resistors.
Worked example: unknown resistance
Let R₁ be 1,000 ohms, R₂ 2,000 ohms and R₃ 500 ohms at balance. Then Rₓ = 500 × 2,000 ÷ 1,000 = 1,000 ohms. The calculator prints the resistance and the sum. The page does not print a numerical example, so this example is our own. Use any consistent unit, such as ohms or kilohms, and the answer comes back in the same unit.
Output voltage of an unbalanced bridge
If the bridge is not balanced, the meter reads a small voltage. The output V_G is the voltage of node D relative to node B [1]. With the two voltage dividers, it is V_G = (R₂ ÷ (R₁ + R₂) − Rₓ ÷ (Rₓ + R₃)) × V_s. The Wikipedia page's equation was garbled in the text our tool read, so we state this form as our own working from the two dividers, which gives the same balance condition.
Worked example: the voltage
Take V_s = 5 volts, R₁ = R₂ = R₃ = 1,000 ohms and Rₓ = 1,100 ohms. The first divider gives 0.5. The second gives 1,100 ÷ 2,100 = 0.52381. So V_G = (0.5 − 0.52381) × 5 = −0.11905 volts, or −119.05 millivolts. The sign tells you that node D is below node B, so Rₓ is higher than the balance value of 1,000 ohms.
Sign and balance
A positive output means node D is above node B, and a negative output means it is below. When the output is zero, the bridge is balanced. The calculator also tells you the balance resistance Rₓ would need, which equals R₃ × R₂ ÷ R₁. That helps you see how far the unknown resistor is from the balance point.
Uses of the bridge
The bridge is used to measure resistance accurately, and with a sensor in place of Rₓ it turns a small change in resistance into a small voltage. Strain gauges, thermistors and light sensors are often used this way. The output voltage is small, so it is normally amplified. The page here gives the ideal value for a meter with infinite resistance.
Limits of the ideal model
The calculator treats the meter as ideal, with no current drawn, and the resistors as exact. In practice, the meter resistance, lead resistance, temperature changes and self-heating of the resistors cause errors. The supply voltage also sets how much power each resistor dissipates, so choose a safe level. Treat the result as an ideal value.
Using the calculator
Pick the mode, then enter the resistors with the same unit. For the balance mode, you only need R₁, R₂ and R₃. For the voltage mode, enter all four resistors and the supply voltage. If you need the supply to be exact, check it with a meter. Change one resistor at a time to see how the output moves.
Choosing resistor values
For a sensor bridge, designers often make all three fixed resistors equal to the sensor's resting resistance, so the bridge starts balanced and the output is zero at rest. A small rise in the sensor resistance then produces a small output voltage, as in the example above, where a 10 percent rise gives about 119 millivolts at 5 volts of supply. A larger supply gives a larger output, but it also heats the resistors, so pick the supply with care. Test several values in the calculator to see the trade-off between the output size and the heat.
Checking your result
You can check a balanced answer by working the two dividers by hand. With R₁ = 1,000, R₂ = 2,000, R₃ = 500 and Rₓ = 1,000 ohms, the first divider gives 2,000 ÷ 3,000 = 0.6667 and the second gives 1,000 ÷ 1,500 = 0.6667, so the output is zero. If the two numbers differ, the bridge is out of balance, and the difference times the supply is the output voltage.
Common mistakes
- Swapping R₁ and R₃. The balance formula has R₃ times R₂ over R₁, so keep the labels from the diagram.
- Mixing ohms and kilohms. Use one unit for every resistor.
- Expecting the supply to matter at balance. At balance, the result is independent of the voltage.
- Ignoring the meter resistance. The ideal model assumes none.
What next
Use this often? Add Wheatstone B to your Home screen.
Frequently asked questions
How does a Wheatstone bridge calculator work?
At balance it uses Rx = R3 × R2 ÷ R1. For an unbalanced bridge it uses two voltage dividers to find the output voltage.
What is the balance condition?
R2 divided by R1 equals Rx divided by R3, and the meter reads zero.
Does the supply voltage matter at balance?
No. At balance, no current flows through the meter, so only the ratios matter.
What does a negative output voltage mean?
Node D is below node B, so Rx is above its balance value.
Can I use kilohms?
Yes, if every resistor uses the same unit. The answer comes back in that unit.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.