A watts to amps calculator turns a power in watts into a current in amps when you know the voltage. It covers direct current, single-phase AC with a power factor and balanced three-phase AC, so it also answers the wattage to amperage question for a motor, a heater or a charger.
How to use the watts to amps calculator
- Choose DC, single-phase AC or three-phase AC.
- Enter the power in watts and the voltage.
- For AC, add the power factor, or leave it blank for 1.
- Press Calculate to read the current in amps.
The idea: power, voltage and current
Electrical power is the product of voltage and current, so for direct current the current is the power divided by the voltage: I = P ÷ V. A 1,500 watt heater on a 120 volt supply draws 1,500 ÷ 120 = 12.5 amps. The same relation holds for a resistive AC load with a power factor of 1. The calculator shows the sum it used, so you can check it against a nameplate.
Why AC needs a power factor
In an alternating current circuit, the current and voltage may not rise and fall together. The power factor is the ratio of the real power absorbed by the load to the apparent power flowing in the circuit, and the apparent power is the product of the RMS current and voltage [1]. The real power is the apparent power times the cosine of the phase angle between current and voltage [1]. So, in single-phase AC, the current is I = P ÷ (V × PF), a larger current than the DC sum when the power factor is below 1.
Single-phase worked example
A motor takes 1,500 watts from a 120 volt single-phase supply at a power factor of 0.8. The current is 1,500 ÷ (120 × 0.8) = 15.625 amps. The apparent power is 1,500 ÷ 0.8 = 1,875 volt-amperes. The calculator shows both. The extra 3.125 amps compared with the 12.5 amps of a unity power factor load are carried by the wiring but do no useful work.
Three-phase supplies
For a balanced three-phase load, the line-to-line voltage is √3 times the line-to-neutral voltage [2]. The standard result is that the real power is √3 × V × I × PF, with V the line-to-line voltage and I the line current, so the line current is I = P ÷ (√3 × V × PF). That formula is the standard textbook one, and the Wikipedia page we opened gives the √3 relation between the voltages but not that final line, so we state it as our own working from it. A 10,000 watt load at 400 volts and a power factor of 0.9 draws 16.038 amps per line.
Reading the result
The main figure is the current in amps, with the same value in milliamps. For AC, the calculator also shows the apparent power in volt-amperes and kilovolt-amperes next to the real power in watts and kilowatts. The apparent power is the figure that sizes a supply or a generator, while the real power is what the load actually uses. Use the amps figure as the line current of one conductor.
If you do not know the power factor
Many resistive loads, such as a kettle or a toaster, have a power factor close to 1, so leaving the box blank is a fair first guess for them. Motors, transformers and fluorescent ballasts have lower values, often printed on the label. If you leave the box blank, the page says that it assumed 1. A lower power factor always raises the current, so an assumption of 1 gives the lowest current you can expect.
DC examples
In a direct current circuit there is no power factor and no phase angle. A 60 watt car accessory on a 12 volt supply draws 60 ÷ 12 = 5 amps. A 100 watt solar panel at 18 volts delivers about 5.56 amps. Choose direct current in the first box and the power factor box disappears. Use the voltage that the device sees at its terminals, not the battery label if there is a long cable.
Wattage to amperage in other words
People also search for wattage to amperage, watts to current and watts to amps conversion. They all mean the same sum: divide the power by the voltage, and for AC also by the power factor, and for three-phase also by √3. The result is a current in amps. To go the other way, from amps to watts, multiply instead of dividing.
Limits and safety
The page assumes a balanced three-phase load and a steady voltage. It does not include the starting surge of a motor, voltage drop in a long cable, harmonics or the efficiency of a device. Never size a cable, a fuse or a breaker only from this result. A licensed electrician must check the real sizing against the code that applies where you live.
Common appliance examples
A 2,000 watt electric kettle on a 230 volt supply draws about 8.7 amps, and a 1,000 watt microwave oven on 120 volts draws 8.3 amps if its power factor is near 1. A small three-phase pump motor of 5,000 watts at 400 volts and a power factor of 0.85 draws about 8.5 amps per line. These quick examples show why the same wattage gives a smaller current on a higher voltage, which is the reason long power lines use high voltages.
Common mistakes
- Using the line-to-neutral voltage for three-phase. Enter the line-to-line voltage, such as 400 volts, not 230 volts.
- Forgetting the power factor for a motor. A power factor of 0.8 raises the current by a quarter compared with 1.
- Mixing up watts and volt-amperes. The label may show the apparent power, which already includes the power factor.
- Using the result to pick a breaker. The calculator is an estimate, not a design.
What next
Use this often? Add Watts to Amp to your Home screen.
Frequently asked questions
How do I use a watts to amps calculator?
Choose the supply type, enter the watts and the volts, add the power factor for AC, and press Calculate.
What is the formula for watts to amps?
For DC, amps equal watts divided by volts. For single-phase AC, divide by volts times the power factor. For three-phase AC, divide by √3 times volts times the power factor.
What power factor should I use?
Use the value on the label. Resistive loads are close to 1 and motors are often 0.8 to 0.9.
Which voltage do I enter for three-phase?
The line-to-line voltage, for example 400 volts.
Can I use the result to choose a breaker?
No. It is an estimate, and a licensed electrician must check real sizing against the code.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.