How to join videos
- Add two or more clips. You can use MP4, M4V, MOV, WEBM or MKV.
- Use the arrows to put them in order.
- Choose Join videos, and download your MP4 when it’s ready.
What happens to your clips
- Size: the result takes its shape from the first clip, up to Full HD (1920 pixels wide). Clips of another shape get black bars, so nothing is cut off or stretched.
- Quality: every clip is re-encoded into MP4 (H.264 video and AAC audio), so you may see a small loss of quality, and the file size can change.
- Sound: each clip keeps its own sound. A clip with no sound stays silent for its length.
How long will it take?
Your own device does the work, so speed depends on its power and on how long the clips are. A clip can take about as long as its running time, or longer on older phones. Keep the tab open until it’s done. Add up to 20 clips and 2 GB in all. Very long videos can run out of memory, especially on phones.
Is it private?
Yes. Your clips stay on your device, and nothing is uploaded. This tool joins clips end to end, but it doesn’t trim or add transitions.
Is the result too big? Use the video compressor to make it smaller.
Video joiner worked example: three clips into one
Say you add three clips from a trip, in this order:
- Clip 1: 12.5 seconds, 2560 × 1440
- Clip 2: 30 seconds, 1920 × 1080
- Clip 3: 8 seconds, 1280 × 720
The video joiner places them end to end. Clip 1 starts at 0 seconds, clip 2 at 12.5 seconds and clip 3 at 42.5 seconds, so the joined video runs for 50.5 seconds. Because the first clip is wider than 1920 pixels, the result is scaled down to 1920 × 1080. Clip 3 has the same shape, so it fills the frame with no bars; it’s scaled up to match the rest of the video.
The video is encoded at about 4,000 kbps and the sound at 128 kbps, which works out at roughly 31 MB a minute. For 50.5 seconds, expect a file of around 26 MB. The real size can differ a little, because the encoder treats the bitrate as a target.
Why the first clip matters
The first clip in the list sets the size and shape of the whole video. Its width is limited to 1920 pixels, and a smaller clip is never enlarged. Both sides are rounded to even numbers, which video encoders need.
| First clip | Joined video |
|---|---|
| 3840 × 2160 (4K) | 1920 × 1080 |
| 2560 × 1440 | 1920 × 1080 |
| 1280 × 720 | 1280 × 720 |
| 1080 × 1920 (vertical phone video) | 1080 × 1920 |
| 4096 × 2160 | 1920 × 1012 |
So if most of your clips are vertical, put a vertical clip first. A landscape clip placed after it then gets black bars above and below, and the reverse happens when a landscape clip comes first.
File types it accepts
The joiner takes files ending in .mp4, .m4v, .mov, .webm or .mkv. Other files aren’t added, and a message names the file. The output is always MP4, which MDN calls a popular container that supports several of the most-used codecs and is broadly supported.[1] WebM, by contrast, is based on Matroska and designed for the web.[1] A clip can only be joined if your browser can read the codec inside it. If it can’t, you see a message that one of your clips couldn’t be read. A file with sound but no picture is refused too.
Why it needs an up-to-date browser
The joiner relies on the browser’s own video tools. The WebCodecs API lets a web page encode and decode video and audio in the browser, using hardware acceleration where available.[2] Before it starts, the joiner checks that your browser can make H.264 video. If not, it asks you to use Chrome or Edge on a computer. It also checks for AAC sound; without it, the video is made silent and the result says so.
Tips for a smoother result
- Use clips with the same shape. Clips filmed on one phone or camera in the same orientation fill the frame with no bars.
- Join in smaller groups. With more than 20 clips, join them in groups, then join the resulting MP4 files together.
- Keep a laptop plugged in. Your own device does all the encoding, and a long join can use a lot of power.
- Check the result. After you download the joined video, play it through, especially where one clip ends and the next begins.
Common mistakes
- Reordering after joining. Moving, removing or adding a clip clears the joined video and stops a join in progress. Put clips in order first, then press Join videos.
- Leaving the page before downloading. The joined MP4 exists only in this tab until you download it.
- Expecting trims or fades. Cut each clip first with the video trimmer, then join them.
How this tool works
You add 2 to 20 clips (MP4, M4V, MOV, WebM or MKV, 2 GB combined at most), put them in order, and the tool joins them into one MP4. It runs in your browser with the mediabunny library, and nothing is uploaded.
The output size comes from the first clip, limited to 1920 pixels wide and never enlarged, with even dimensions. Each frame is drawn on a black canvas at that size, so a clip with a different shape gets bars. Video is encoded as H.264 at 4,000 kbps. Each clip starts when the one before it ends.
Audio is converted per clip to AAC, 48 kHz stereo at 128 kbps, so clips with different audio settings still match. If your browser cannot encode audio, the result is silent and the tool says so.
What next
Use this often? Add Video Joiner to your Home screen.
Frequently asked questions
Can I join videos with different formats or sizes?
Yes. Each clip is converted to match. The result uses the first clip’s shape, and other shapes get black bars.
Are my videos uploaded?
No. The joining happens in your browser, so your videos stay on your device.
Why is it slow?
Your own device re-encodes every clip, which takes time. Newer computers are usually faster than older phones.
Will I lose quality?
A little, because each clip is re-encoded. The result is limited to Full HD at about 4 Mbps.
How many clips can the video joiner combine?
Up to 20 clips at a time, and up to 2 GB in all. You need at least two clips to join.
What happens if I change the order after joining?
The joined video is cleared, because it no longer matches the list. Press Join videos again to make a new one, and download each version you want to keep.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.