This video trimmer cuts a section out of a video by start and end time, entirely in your browser, and saves the result as an MP4.
How this video trimmer cuts a clip
The video trimmer gives FFmpeg two positions. The -ss option sets where to start reading, and -to sets where to stop. [1] Everything between them is kept and everything outside is dropped. Because the clip is encoded again to H.264 video and AAC audio in an MP4 container, [2] it starts exactly at your start time, instead of at the nearest keyframe like a stream copy would.
Worked example
You have a 2 minute recording and want only the part from 0:05 to 0:20. Type 0:05 as the start and 0:20 as the end. The result is 15 seconds long, because 20 minus 5 is 15, and it begins at the frame at 5 seconds. Leave the end box empty and the clip runs from 0:05 to the end of the video, so a 2 minute file would give 1 minute 55 seconds.
Time formats you can type
| You type | Meaning |
|---|---|
| 75 | 75 seconds |
| 1:15 | 1 minute 15 seconds |
| 0:01:15.5 | 1 minute 15.5 seconds |
| (blank end) | Until the end of the video |
The end must be later than the start. If you type an end past the length of the video, FFmpeg simply stops at the last frame.
Video trimmer tips
- Play the file first and note the exact times you want. Phone players show minutes and seconds.
- To cut the middle out of a video, trim the first part and the last part separately and join them in an editor.
- To shrink the file after cutting, run the clip through the video resizer.
- Keep your original. The tool writes a new file and never changes the source.
Privacy, limits and the FFmpeg core
This page runs FFmpeg as ffmpeg.wasm, a WebAssembly build that works inside your browser tab. [3] The first time you press the button the page downloads the converter, about 10 MB, and keeps it for the rest of the visit. Your video is read from your own disk into the browser, processed there and handed back as a download. It is never uploaded, so it works for private recordings and you can use it offline once the converter has loaded.
Files up to 500 MB are accepted. Long or high resolution files take noticeably longer than they would in a desktop program, because a browser build of FFmpeg runs on a single thread and has less memory to work with. Keep the tab open until the progress figure reaches 100%, and press Stop if you change your mind. The FFmpeg core in this build is licensed under GPL-2.0-or-later, which is why the licence note sits under the button.
Step by step with the video trimmer
- Press the upload box and choose your video.
- Type the start time, for example 0:05.
- Type the end time, for example 0:20, or leave it blank for the end of the video.
- Press Trim video and wait for the progress to reach 100%.
- Download the clip and play it to check the start and end.
Who uses the video trimmer
Parents cut the best seconds from a family clip, teachers take one example from a long lecture, and social media creators shorten a recording to fit a time limit. Developers and testers also trim screen recordings to show only the bug.
Common mistakes to avoid
- Typing an end time earlier than the start time.
- Mixing up 1:05 (one minute five) and 1.05 (one second and a bit).
- Trimming a converted copy instead of the original.
- Expecting the tool to cut the middle out of a video; it keeps one section.
Quality, formats and browser notes
Every video this site writes is encoded with the x264 or equivalent encoder at a constant quality, so the picture looks close to the source while the size stays sensible. Most outputs use an MP4 container with H.264 video and AAC audio because that pairing plays on nearly every phone, TV, browser and editor. Chrome, Edge, Firefox and Safari on a computer all run the converter; phones can run it too, but a long clip may be slow or stop if the browser runs short of memory. If that happens, close other tabs, use a shorter clip or work from a computer.
Why the trimmed clip is encoded again
Some programs cut video without re-encoding, which is instant but can only start at a keyframe, a full picture that the frames after it depend on. That can start a clip up to several seconds early. By encoding again, this tool starts the clip exactly where you asked and always produces an MP4 that plays everywhere. The cost is a little time and a very small loss of quality, which for a short clip is hard to see.
If something goes wrong
If the page says the converter could not be loaded, check your internet connection, because the 10 MB core is fetched the first time you use it, and reload the page. If the job fails on a particular file, it may be damaged or use a codec that this browser build of FFmpeg does not include; try opening it in a media player first. If the page stops with a memory error, the file is too large for the browser, so trim it, resize it or use a computer with more memory. Pressing Stop ends the job at once and frees the memory, and you can start again with other settings.
What next
Use this often? Add Video Trimme to your Home screen.
Frequently asked questions
How do I use the video trimmer?
Choose your video, type the start time and the end time, then press Trim video. The clip appears as a download when the progress reaches 100%.
Does trimming reduce quality?
The clip is encoded again, so there is a small generation loss, but at the default quality it looks very close to the original.
Can I leave the end time blank?
Yes. A blank end keeps the video from the start time to the end of the file.
What time formats are accepted?
Seconds, minutes and seconds like 1:05, or hours like 0:01:05, with an optional decimal part.
Is the video uploaded?
No. Trimming happens in your browser, so the video stays on your device.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.