A twist rate calculator estimates how fast a rifle barrel must turn the bullet, as one turn in so many inches, to keep it stable in flight. Enter the bullet diameter and length, choose the Greenhill rule or the Miller rule, and read the twist. With the Miller rule you can also enter a barrel's twist to see its stability factor.
How to use the twist rate calculator
- Choose US or metric units and the method.
- Enter the bullet diameter and length, and the mass for the Miller rule.
- Add the optional values, such as the muzzle velocity or your barrel twist.
- Press Calculate.
Why twist matters
A rifled barrel spins the bullet so that it flies point first. If the spin is too slow the bullet tumbles, and if it is faster than needed the bullet is spun more than it requires. The twist rate is the distance in which the barrel makes one full turn, so a twist of 1 in 12 inches means one turn every 12 inches. Longer, heavier bullets need a faster twist than short ones. The calculator gives the twist that a bullet of your size needs.
The Greenhill rule
The Greenhill rule is a long-standing rule of thumb for the twist of a rifle barrel [1]. The twist is t = C · D² ÷ L · √(SG ÷ 10.9), where D is the bullet diameter and L its length in inches, SG its specific gravity and C a constant. The result is in inches per turn. Wikipedia gives the formula in a garbled form, so we use the standard reconstruction, in which a specific gravity of 10.9, that of a lead-core bullet, makes the second factor equal 1 [1].
The constant C
Wikipedia gives C as 150, with 180 for muzzle velocities above 2,800 feet per second, about 853 metres per second [1]. The calculator uses 150 unless you enter a muzzle velocity above that figure, and then uses 180. The step from 150 to 180 makes the required twist 20 percent faster, so a fast load gets a faster twist. Leave the velocity blank for a normal speed.
Specific gravity
The specific gravity, the density of the bullet relative to water, enters through the factor √(SG ÷ 10.9). Wikipedia gives 10.9 for lead-core bullets, which cancels that factor [1], so the box is optional. If you leave it blank, the calculator uses 10.9, which makes the factor 1. A denser bullet, such as one with a solid copper-alloy or tungsten core, needs a slightly different twist, so enter your value if you know it.
The Miller rule
The Miller rule works from the stability factor s = 30 m ÷ (t² D³ l (1 + l²)), where m is the mass in grains, D the diameter in inches, l the length in calibers and t the twist in calibers per turn [2]. Solving for t gives the twist that you need for a chosen s, and the twist in inches is T = t × D [2]. The rule includes the mass, so it distinguishes between a light and a heavy bullet of the same size, which Greenhill does not.
A worked example
Take a 168 grain bullet with a diameter of 0.308 inches, a length of 3.98 calibers and a stability factor of 1.8. Then t² = 1,429.8, t = 37.81 and the twist is 11.646 inches per turn. The calculator asks for the length in inches and divides it by the diameter. A length of 1.226 inches is 3.98 calibers, and the result is the same 11.646.
The stability factor
Miller suggests 2.0 as a safe stability factor for rough estimates [2], and the calculator uses it as the default. The bands it reports are its own working convention: below 1 is unstable, from 1 to 1.5 marginally stable, and above 1.5 adequately stable, with exactly 1.5 placed in the marginal band. If you enter your barrel twist, the calculator reports the stability factor and the band that it falls in.
Greenhill and Miller together
For a 0.308 inch bullet 1.226 inches long, Greenhill gives 11.61 inches per turn and Miller with a stability factor of 1.8 gives 11.65, so the two agree closely for a conventional bullet. They can disagree for very long, light or unusual bullets. Running both is a quick sanity check. If the numbers differ, prefer the faster twist, or test with real ammunition before deciding on a barrel.
What the tool leaves out
Real stability also depends on velocity, altitude and temperature. The calculator does not correct for them, apart from the step in the constant C. Wikipedia describes the constant 30 in the Miller rule as a rough approximation of standard conditions [2]. Stability also depends on the shape of the bullet, the position of its centre of gravity and the air. The result is a guide to the twist that you should look at, and it is not a promise that a barrel will stabilize a given bullet in the field.
Units
In US mode the diameter and length are in inches, the mass in grains and the velocity in feet per second. In metric mode they are in millimetres, grams and metres per second, and are converted before the formula is used, with 25.4 millimetres to the inch, 0.3048 metres to the foot and 0.06479891 grams to the grain. The twist is shown in inches or millimetres per turn, both as a length and as the one-turn-in form.
Common mistakes
- Entering the length in calibers. The calculator wants the length in inches or millimetres.
- Using the same twist for every bullet weight. Heavier, longer bullets need faster twists.
- Treating the result as a guarantee. Check by test firing.
- Mixing grains and grams. Use the unit shown in the box.
What next
Use this often? Add Twist Rate to your Home screen.
Frequently asked questions
What is a twist rate calculator?
A tool that estimates how fast a rifle barrel must spin a bullet, as one turn in so many inches, from the bullet's size.
What is the Greenhill formula?
t = C · D² ÷ L · √(SG ÷ 10.9), with C = 150, or 180 above 2,800 ft/s, giving inches per turn.
What is a good stability factor?
This tool treats above 1.5 as adequately stable. It uses 2 as a safe default, which is Miller's suggestion for rough estimates.
Why does the Miller rule need the mass?
Because the stability factor depends on the bullet mass as well as its size.
Can I rely on the result for a barrel choice?
Use it as a starting point and check with test firing.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.