A ballistic coefficient calculator finds the ballistic coefficient of a bullet from its mass, its diameter and its form factor. It also shows the sectional density, and can work the other way round to find the form factor from a published ballistic coefficient. It accepts grains and inches, or grams and millimetres.
How to use the ballistic coefficient calculator
- Choose US or metric units.
- Enter the mass and the diameter of the bullet.
- Enter the form factor, or choose to find it from a ballistic coefficient.
- Press Calculate.
What it measures
The ballistic coefficient is a measure of the ability of a body to overcome air resistance in flight, and it is inversely proportional to the negative acceleration [1]. A bullet with a high ballistic coefficient keeps its speed better, drops less and drifts less in the wind. The physics form is C_b = m ÷ (C_d A), with m the mass, A the cross-section and C_d the drag coefficient [1].
The projectile form
For bullets, the page gives C_b = m ÷ (d² i), where d is the diameter and i the form factor [1]. The ratio m ÷ d² is the sectional density, so the ballistic coefficient is the sectional density divided by the form factor. The form factor is the ratio of the drag coefficient of the bullet to that of a standard projectile [1]. For a standard projectile, the form factor is 1 and the coefficient is 1.00 [1].
Sectional density
Sectional density is the mass divided by the square of the diameter. For a bullet of 175 grains and 0.308 inches, the mass is 0.025 pounds, taking 7,000 grains to the pound, a figure that is our own, and the sectional density is 0.025 ÷ 0.308² = 0.26354 pounds per square inch. In metric units, a bullet of 11.34 grams and 7.82 millimetres has 185.438 kilograms per square metre, which is the same quantity.
Units
The page gives the unit as kilogram-force per square metre, or pounds per square inch, where one pound per square inch corresponds to 703.06957829636 kilogram-force per square metre [1]. The calculator shows both. It works internally in pounds per square inch, which is what most published ballistic tables use, and converts the metric inputs to those units.
A worked example
With a sectional density of 0.26354 pounds per square inch and a form factor of 0.5, the ballistic coefficient is 0.52707 pounds per square inch. A form factor below 1 means that the bullet has less drag than the standard projectile, so the coefficient is higher than the sectional density. A blunt bullet with a form factor of 1.2 would have a coefficient lower than its sectional density. The example is our own calculation.
Finding the form factor
Manufacturers publish the ballistic coefficient. With the mass and the diameter, you can find the form factor, which is the sectional density divided by the coefficient. A 175 grain, 0.308 inch bullet with a published coefficient of 0.4 has a form factor of 0.65884. Use the second mode of the calculator for this. The form factor is a handy way to compare bullet shapes independent of weight.
Standard models
The coefficient is always tied to a standard drag model, such as G1 or G7. The page notes that G1 was the old Type 1 projectile, renamed by the Aberdeen Proving Ground, and that the coefficient for one model differs substantially from the coefficient of the same bullet for another [1]. Never compare a G1 value with a G7 value. The calculator does not choose a model: you must keep to the one that your data uses.
Heavier and longer bullets
For the same diameter and the same shape, a heavier bullet has a higher sectional density and, so, a higher ballistic coefficient. This is why long, heavy bullets are favoured for long-range shooting. Doubling the mass at the same diameter and form factor doubles the coefficient. The calculator makes this easy to see: change only the mass and watch the result.
Limits
The ballistic coefficient is a simplification. It treats the drag of a bullet as a constant multiple of a standard curve, and in reality the coefficient changes with speed. For accurate long-range work, use the full drag tables for the bullet, and a ballistic solver. The calculator is for comparing bullets and for finding the values that tables need.
Effect of the bullet weight
For a 0.308 inch bullet with a form factor of 0.5, a weight of 150 grains gives a coefficient of 0.4518, 175 grains gives 0.5271 and 200 grains gives 0.6024. The sectional densities are 0.22588, 0.26354 and 0.30118 pounds per square inch. Each added grain raises the coefficient in proportion, since the diameter and the shape do not change. These are our own calculations from the formula.
Reading published figures
Published coefficients are usually measured with a particular drag model and at particular speeds. When two makers quote different values for similar bullets, check that they use the same model, and whether the value is an average over a range of speeds or the figure at one speed. The calculator gives you the sectional density from the weight and the diameter, which does not depend on any of those choices.
Common mistakes
- Mixing G1 and G7 values. Keep to one model.
- Using the wrong mass unit. Grains are not grams.
- Entering the radius as the diameter. Use the diameter.
- Treating the coefficient as constant. It varies with speed.
What next
Use this often? Add Ballistic Co to your Home screen.
Frequently asked questions
What is a ballistic coefficient calculator?
A tool that finds the ballistic coefficient of a bullet from its mass, diameter and form factor.
What is the formula for the ballistic coefficient?
C_b = m ÷ (d² i), the sectional density divided by the form factor.
What is sectional density?
The mass divided by the square of the diameter.
How do I convert lb/in² to kg/m²?
Multiply by 703.06957829636.
What is a form factor?
The ratio of the drag coefficient of the bullet to that of the standard projectile.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.