Saved

Press the star next to a tool's name to save it.

All my tools

Titration Calculator

Use this titration calculator to find the unknown concentration or volume of an acid or base from the equivalence point, with acids and bases that give more than one hydrogen or hydroxide ion.

Restored your last values ·

Enter the concentration and volume of the acid and the concentration or the volume of the base, and leave empty the one you want. Add the number of hydrogen and hydroxide ions per formula unit if they are not 1. You get the missing value and the moles that react.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Fill in three of the four boxes, then press Calculate.

See full result

A titration calculator finds the unknown concentration or volume in an acid-base titration from the stoichiometry of the neutralization. Enter the concentration and volume of the acid and the volume of base needed to reach the equivalence point, and it gives the concentration of the base. It can solve for any one of the four quantities, and it works for acids and bases that give more than one hydrogen or hydroxide ion.

How to use the titration calculator

  1. Enter the concentration and volume of the acid.
  2. Enter the volume of the base at the equivalence point, or its concentration. Leave empty the box that you want to find.
  3. Change the ions per formula unit if the acid or base is not monoprotic.
  4. Press Calculate.

The equation

For an acid AHₙ and a base B(OH)ₘ, the page on neutralization writes the balance as n × v₁ × c₁ = m × v₂ × c₂, where v and c are the volume and the concentration of the acid and the base [2]. In words, the volume of the acid times the concentration of hydrogen ions it gives equals the volume of the base times the concentration of hydroxide ions [2]. For a strong acid and a strong base the reaction reduces to H⁺ + OH⁻ → H₂O [2]. When each has one ion this is the familiar C₁V₁ = C₂V₂.

Worked example

A sample of 25.0 mL of 0.100 mol/L hydrochloric acid needs 20.0 mL of sodium hydroxide to reach the equivalence point. The acid holds 0.100 times 25.0, which is 2.50 millimoles, so the base is 2.50 divided by 20.0, which is 0.125 mol/L. This is our own example. Leave the volume of the base empty and enter 0.125 mol/L to see that 20 mL is needed.

Equivalence point and end point

The equivalence point is where chemically equivalent quantities of the reagents have been mixed, and the amounts are in the ratio of the chemical equation, which does not necessarily mean 1 to 1 [3]. The end point is where the indicator changes colour in a titration with colour, and it is related to the equivalence point without being the same [3]. A good indicator changes colour close to the pH of the equivalence point, so the difference is small. The titration page says the equivalence point is set by the stoichiometry, and that simple stoichiometric calculations then give the molarity of the unknown [1].

Polyprotic acids

Sulfuric acid gives two hydrogen ions per molecule, so n = 2. A sample of 20.0 mL of 0.100 mol/L sulfuric acid holds 4.00 millimoles of hydrogen ions and needs 40.0 mL of 0.100 mol/L sodium hydroxide, which gives one hydroxide ion per unit. Enter 2 for the hydrogen ions per acid molecule. Barium hydroxide gives two hydroxide ions, so enter 2 for the base. The calculator treats both ions as fully released, which is the case for strong acids and bases.

The pH at the equivalence point

The page on neutralization says that the pH of the solution after neutralizing a strong acid with a strong base is close to 7, and that the exact value depends on the temperature [2]. For a weak acid and a strong base, the pH at the end point is above 7 because the conjugate base of the acid raises it [2]. For a weak base and a strong acid it is below 7. The calculator reminds you of this after each result but does not work out the pH.

Doing the titration

Rinse the burette with the titrant, fill it, and record the starting level. Add a few drops of indicator to the sample, run in the titrant while swirling, and slow down as the colour begins to linger. Record the final level and subtract. Repeat until two results agree, and use the mean volume. Use that mean in the calculator.

Common uses

Titration is used to find the acidity of vinegar, the alkalinity of water, the strength of antacids and the purity of a chemical. The same relation holds for any reaction in which one reactant is added to another until the reaction is complete, though the stoichiometric ratio changes with the reaction.

Choosing an indicator

An indicator is a weak acid or base whose colour differs between its two forms, and it changes colour around its own pKa. Choose one whose colour change falls close to the pH at the equivalence point. For a strong acid with a strong base, the pH rises very steeply through 7 at the equivalence point, so many indicators work. For a weak acid with a strong base the equivalence point is above 7, so pick an indicator that changes at a higher pH. The calculator finds the amounts, and the choice of indicator decides how close the end point comes.

Common mistakes

  • Forgetting polyprotic acids. Enter the number of hydrogen ions per molecule.
  • Mixing mL and L. Keep both volumes in millilitres.
  • Reading the end point as the equivalence point. They can differ a little.
  • Using only one run. Repeat the titration and use the mean.

What next

Use this often? Add Titration to your Home screen.

Frequently asked questions

What is a titration calculator?

A tool that finds an unknown concentration or volume in an acid-base titration from the equation n₁c₁v₁ = n₂c₂v₂.

How do I calculate the concentration of the unknown?

Multiply the concentration and volume of the known solution and the ions per formula unit, and divide by the volume and ions of the unknown. 25 mL of 0.100 M HCl and 20 mL of base gives 0.125 M.

What is the equivalence point?

The point where chemically equivalent amounts of acid and base have been mixed. It does not always mean a 1 to 1 ratio.

What is the difference between end point and equivalence point?

The end point is where the indicator changes colour. The equivalence point is set by the stoichiometry, and the two are close but not always the same.

What pH does a strong acid and base give at equivalence?

Close to 7, with the exact value depending on temperature.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools