Saved

Press the star next to a tool's name to save it.

All my tools

Stress Concentration Factor Calculator

Use this stress concentration factor calculator to find Kt for an elliptical hole from its half-length and half-width or tip radius, and the peak stress from the nominal stress.

Restored your last values ·

Choose how you describe the hole. Enter its half-length across the load and either its half-width or the radius at its end. Add the nominal stress to get the peak stress.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the half-length and the half-width (or tip radius), then press Calculate.

See full result

A stress concentration factor calculator shows how much a hole or notch raises the stress in a loaded plate. Enter the shape of an elliptical hole, and it returns the factor Kt, and the peak stress if you give the nominal stress.

How to use the stress concentration factor calculator

  1. Choose US or metric units for the stress.
  2. Choose whether to describe the hole by its half-width or its tip radius.
  3. Enter the half-length across the load and the second dimension.
  4. Add the nominal stress if you want the peak stress, then press Calculate.

What the factor means

The page defines the stress concentration factor as the ratio of the highest stress, σmax, to a nominal stress, σnom, of the gross cross-section [1]. So Kt = σmax ÷ σnom. A factor of 1 means no concentration at all. A factor of 3 means that, at the worst point, the material feels three times the stress that you would calculate by dividing the load by the area.

Why holes raise the stress

Forces in a loaded part flow around any interruption, such as a hole, a notch or a sudden change of section. The lines of force crowd together at the edge of the hole, and the local stress rises there. Away from the hole, the stress returns to the nominal value. The calculator quantifies this crowding for one standard shape, the ellipse, which is a good model for many holes and slots.

Inglis' equation

For an elliptical hole of length 2a and width 2b under a far-field stress σ0, the page gives the stress at the ends of the major axis by Inglis' equation [1]. The formula appears as σmax = σ0 (1 + 2a ÷ b) = σ0 (1 + 2 √(a ÷ ρ)). The text we could read had lost the fraction and radical signs, so this is our reading of it, and it agrees with the standard form of the equation.

The circular hole

For a circular hole in an infinite plate, where a = b, the page states that the stress concentration factor is 3 [1]. This is a good check on the formula, because 1 + 2 × 1 = 3. A small round hole in a wide plate under tension therefore carries a peak stress of three times the nominal stress, at the sides of the hole that are at right angles to the pull.

Long and short holes

A hole that is long across the load, with a larger than b, has a factor above 3. A slot of 2 to 1 across the load gives a factor of 5. A hole that is long along the load, with a smaller than b, has a factor below 3. A slot of 1 to 4 gives 1.5. In both cases the factor depends only on the ratio a ÷ b, not on the size of the hole, which is why you can use any length unit.

The tip radius

The same equation can be written with the radius of curvature ρ of the hole at the end of the major axis, which is the second form that the calculator accepts [1]. A smaller radius means a sharper end and a higher factor. With a = 10 and ρ = 1, the factor is 1 + 2 √10, which is about 7.32. Blunting a sharp corner, for example by drilling a stop hole or rounding a notch, therefore reduces the peak stress.

Sharp cracks

As the radius of curvature approaches zero, such as at the tip of a sharp crack, the page says that the maximum stress approaches infinity [1]. The factor then no longer describes the part in a useful way. This is our advice, not the page's: for a crack-like flaw, use fracture mechanics and a stress intensity factor, and do not rely on Kt.

Peak stress

Enter the nominal stress to see the peak stress: σmax = Kt × σnom. With a nominal stress of 100 MPa and a factor of 5, the peak is 500 MPa. In US mode, a nominal 10,000 psi with a factor of 3 gives 30,000 psi. Compare the peak stress with the strength of the material in the same units, remembering that the nominal stress is the load divided by the gross area, not the net area.

What the tool does not cover

The page's formula is for an elliptical hole in a wide plate, in the elastic range, under a far-field tension. We could not open the Peterson charts, so shoulder fillets, grooves, keyways, finite widths and bending or torsion loads are not included. The direction of the load is also not stated on the page: our reading is that a is the half-length across the load, which is the case that gives the high factor.

Fatigue and brittle parts

Stress concentrations matter most for fatigue, where cracks start at the point of highest stress, and for brittle materials, which cannot yield to relieve the peak. A ductile part under one steady load may yield locally and survive. These remarks are our own general notes. The calculator gives only the elastic factor, and real parts need test data and a safety margin chosen by an engineer.

Common mistakes

  • Using the net area for the nominal stress. The page defines it on the gross cross-section.
  • Mixing a and b. a is the half-length across the load.
  • Applying it to a sharp crack. The stress there has no finite peak.
  • Ignoring the safety margin. An engineer must check real parts.

What next

Use this often? Add Stress Conce to your Home screen.

Frequently asked questions

What is a stress concentration factor calculator?

A tool that finds the factor Kt, the ratio of the peak stress to the nominal stress, for a hole or notch.

What is the stress concentration factor of a circular hole?

3, for a circular hole in an infinite plate.

Does the size of the hole matter?

Not for an ellipse: only the ratio of its half-length to its half-width, or to its tip radius, matters.

Can I use Kt for a crack?

No. The stress at a sharp crack tip grows without limit, so use fracture mechanics.

Does the calculator use Peterson charts?

No. It covers the elliptical hole only.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools